Your kitchen knife becomes dull when the metal at the primary edge, the cutting edge becomes fatigued and rolls over to one side or both sides of the blade. This is normal, it should happen regardless of the quality of the steel and what you are using the knife for. The difference will be “when” it gets fatigued, the better the steel the longer the edge will hold out, generally speaking. However, I have noticed something with high quality knives such as a Fujiwara and this may be applicable to you: I have several different brands of knives ranging from mediocre to my one dream knife. Theoretically, the mediocre knives with their mediocre steel should become dull faster under normal use. (I am referring to use at home, not in professional kitchen and not in the hands of someone who cuts lotus blossoms all day long)
One thing about this stone is that it is very "thirsty." I had a cup of water close by just to add a little water periodically when it felt like it was scraping a little too aggressively. Also, be sure to do as the instructions say and use different parts of the sharpening surface. I wasn't paying attention the first few minutes, and apparently I would end each sharpening pass in the exact same spot, creating a very very small notch on the edge of the stone. So I turned the stone around and made sure to vary the ending spot, and it seemed to buff out that little notch very quickly. My knife is now incredibly sharp--it seems to glide through material rather than "cut" it. I know some people would continue to go even higher with the grit, but for my purposes this whetstone is just perfect. I'll be tackling the kitchen knives next!
One of the most well-regarded natural whetstones is the yellow-gray "Belgian Coticule", which has been legendary for the edge it can give to blades since Roman times, and has been quarried for centuries from the Ardennes. The slightly coarser and more plentiful "Belgian Blue" whetstone is found naturally with the yellow coticule in adjacent strata; hence two-sided whetstones are available, with a naturally occurring seam between the yellow and blue layers. These are highly prized for their natural elegance and beauty, and for providing both a fast-cutting surface for establishing a bevel and a finer surface for refining it. This stone is considered one of the finest for sharpening straight razors.
Made in the USA means a lot! It sharpens quickly, whether you need to remove a lot or just a "tune up" on the blade edges. Because it's manufactured flat, it is excellent for planer blades and chisels. The ability to sharpen dry or with only water creates less of a mess than other types of sharpening stones. The no-hassle guarantee is a definite plus, though I would be surprised if you ever needed it.
I've only used it to touch up the edge on an ESEE RB3 and a pocket folder so far, but it has done very nicely for those tasks. I found that using the rounded edge works best for me in order to be able to run the length of the blade without hitting the leather lanyard. I'll hopefully try it out soon on fish hooks, too. A worthy and handy accessory, and cool looking necklace, to boot!
The toughest angle to master is the angle at which you'll sharpen the edge of the knife. For a Japanese knife, that should be around 12-15 degrees. Before you reach for the protractor, a good test is to get roughly half an index finger's gap between the spine of the knife and the stone (see above). Remember to remove your finger before you start sharpening. For a Western-style knife, you want an angle of about 20°, so raise it ever-so-slightly higher.
The AccuSharp Sharpener is proof positive that you shouldn’t judge a book by its cover. While it looks like something used to attach buttons to shirts it’s actually one of the most cost effective, and we mean effective, means around for restoring a professional edge to your dull knives. It’s compact, screwed together rather than glued and its diamond coated tungsten carbide wheels create an edge that will last.
You need the right size of sharpening stone that fit the type and size of your blades and tools. In general, 6-inches stones are the smaller models and 8-inches are the larger ones. The stones larger than 8 inches are work best for big-sized blades and tools. You may also find sort of ‘pocket knife sharpener’ out there. Most of the credit card sized sharpening stone are smaller than 6 inches and ideal for on the go sharpening not for regular basis.
But it's a different type of sharp, according to Joe Authbert, product development manager at ProCook. "What it does is add tiny little micro-serrations onto the edge of the blade." But fear not - your smart knife won't end up looking like a bread knife, as you'll be hard-pressed to spot the serrations. "If you looked at it under a microscope, on the cutting edge, there are these little lines that generate the sharpness, rather than a waterstone which is a smooth sharp edge," says Authbert.
Begin with your lower-grit stone. Place the heel of your knife on the far edge of the stone, holding the blade gently but firmly with both hands at a 15- to 20-degree angle. Using even pressure, slowly drag the knife over the stone toward you down the length of the stone while simultaneously moving the knife such that the contact point moves toward the tip of the blade.
I'm a novice knife sharpener. I've had to unlearn what my grandpa taught me in order to use these. So far, I've had decent but mixed results. I've switched to my cheap 200/400-ish cheap tool stone from harbor freight for cutting a bevel when the blade has either been damaged or did not have a proper bevel. The 400/1000 grit stone in this kit is soft. Very soft. I have bowled it out several times. It makes keeping a steady angle difficult. But these stones at this price point are meant for learning, and for that they serve their purpose.
HIGH-QUALITY DOUBLE-SIDED KNIFE SHARPENING STONE: Coarse side 1000 grit leaves metal edge with frosted appearance. Edge sharpness equivalent to majority of factory edges on knives, tools; Fine side 4000 grit is ideal for finishing and polishing the edge, make edge very sharp, and edge reflects light well. Perfect for light touch-ups to an already sharp.
An important but often confusing area of sharpening is knowing when you're done with one stone and ready for the next finer grit. On coarse stones it is very easy. When you sharpen one side you will notice a burr forming on the opposite side of the edge. This burr is hard to see but is easy to feel. Very carefully feel for the burr by gently running your hand from the spine to the edge. (Do not run your finger along the knife edge from heel to tip, that's only asking for trouble!) A burr is formed when your stone removes material directly at the edge. The burr will move from one side of your knife to another as you alternate sharpening sides. Make sure you have felt the burr jump between both sides before you move on to the next finer stone. That will ensure that you have sharpened both sides effectively. The finer grits are done the same way but the burr is much smaller. On the finest grits you may not be able to notice the burr at all. Testing the knife sharpness will tell you when you're done. (Learn how you can test to see if your knife is sharp.)