Beginning on the right side of the knife, move from tip to heel and heel to tip, then flip the knife and repeat. For the left side, it’s opposite—start at the top of the stone to reach the heel area completely. So, you will move from heel to tip and then tip to heel. Remember to apply and release pressure as you did earlier, exactly the same as in Step 2, but with light, refining pressure.
Now you may wonder, if a finer stone produces a better cutting edge why do I need a coarse stone at all? The answer is that finer stones work much more slowly than coarse ones. The amount of metal a fine stone removes with each pass is much less than what a coarse stone removes. If you have an edge with a good shape to it from a coarse stone, this is not a problem because the fine stone doesn’t have to remove much metal to improve the edge. If the edge is dull, it will take many times longer to reshape it with a fine stone than it would with a coarse one.
Also natural stones have a random grit size that gives a long lasting edge. Basically the random grits create varying sizes of micro-serration in the blade that wear down at a different rate, therefore longer edge retention. Whether this is true or not we really like natural stone, especially for sharpening tradition single bevel Japanese knives. Use natural stones with water – it’s far cheaper than sake.
You've acquired a good chef's knife, you're using it almost daily to make tasty dinners for the family, and it's stored in a nice knife rack or a magnet for safekeeping. So why stop there? Keeping that knife's edge fine will make cooking not only safer but, let's face it, much more fun. Whether you've spent £150 on a high-end knife or under a tenner on a dinky paring knife, keeping it sharp is crucial.
Therefore, the first step to choosing a whetstone is to determine your intended purpose and then choose your whetstone accordingly. For instance, when sharpening tools that do not require a fine edge, you should choose a relatively soft, coarse, stone such as a Norton Crystolon water stone. However, for sharpening tools that do require a fine edge, a somewhat harder Norton India oil stone would be a good choice. But, for sharpening hunting knives where an exceptionally fine edge is required, a Novaculite or Coticule oil stone would be the best but, most expensive, choice. So, the process of choosing the correct whetstone for any given purpose is to first determine how fast you would like for the stone to cut and how fine an edge you need, and then choose either a soft, coarse, stone or, a hard, fine, stone of the appropriate type and grit.
Why, then, do so many of us shy away from the task? To put it bluntly, it's because it's a rather daunting process for the beginner. Your image of knife sharpening may consist of a hyper-masculine chef slashing away violently at a steel rod (we're looking at you, Gordon). Conversely, you might have seen cooks meticulously and methodically stroking their blade up and down a Japanese waterstone with more intricate attention to detail than a Flemish landscape.
Last, it should be noted that dual-sided Coticule/Belgian Blue whetstones are also sometimes available which have a layer of Belgian Blue stone on one side and a layer of Coticule on the other. Thus, these whetstones provide a softer, more coarse, grit on one side and a harder, finer, grit on the other. Plus, due to the inherent toughness of the Belgian Blue stone, these dual-sided stones do not require a substrate layer.
It is sometimes too confusing on understanding the right sharpener that right to our tools. Then using the chart above you can consider on what is the right stone. Green, red, yellow and blue line they consist of the most familiar and affordable models of sharpening stone to purchase. You can see the performance of each stone in the chart. Silicon Carbide, Aluminum Oxide, and Arkansas they are typically used with the oil (Oil Stones). Waterstones (Synthetic Waterstones) are generally made of Aluminum Oxide too, then people also use oil in place of water with their Waterstone or use water on their Silicon Carbide sharpening stone in place of oil. In this group, Waterstones is the most preferred because of its easy for sharpening edges in shorter time.
Your task as a sharpener is to remove that fatigued metal and expose the steel underneath, the fresh strong steel and bring side A and B of the knife together at the Apex precisely, sounds easy doesn’t it? Like peeling a layer off and having a fresh start, over and over. Of course there is much more to it than this but in very basic terms, you want the abrasive properties of the water stone to abrade the fatigued metal away, like an eraser.
At age 10, Terada learned the basics of sushi from his father and then went on to attend RKC Chef's School in Kochi, Japan from 1987-1989. He soon earned a nickname for his fast knife, attention to detail, divine presentation and ability to create new dishes and accents based on traditional Japanese cuisine. After graduating RKC Chef School, he was called to serve under Master Chef Kondo at Yuzuan restaurant in Kochi, Japan from 1989-1992. Mr. Kondo is the master of Kansai style cooking, considered to be the high-end of Japanese cuisine. Terada earned the title Master Sushi Chef by becoming the standing head sushi chef & can serve Fugu (Japan Licensed) to the public.
My first set of sharpening stones so I have nothing to compare them to. For $50, though, great price to get into the world of sharpening. Stones are great and easy to use. Was able to put hair shaving edges on knives. Took a couple of knives to feel comfortable and better with the process and how to sharpen, but the stones you get work great. Here's the secret though. Get the green leather stoping block as well. As great as the stone are, I have found that stroping the knife after the fact is what really brings out that razor edge. And after using the knife, stroping it again, will restore and keep it razor sharp. Hope you enjoy it as much as I am.