With its premium series Select II, the whetstone manufacturer Sigma Power Corporation from Tokyo addresses users of high-alloy steels such as HSS. These stones, too, are obviously intended to engender a grinding experience similar to that of natural stones. The special production process is expensive, but the Sigma Select II probably has no equal when it comes to demolishing steel.
Rest your knife on the stone at your chosen angle. An easy method for determining the angle by eye is to visualize a 45 degree angle and then take half that amount. That will give you a ballpark estimate of the angle and then you can adjust accordingly up or down. With a slicing action bring the length of the knife across the stone with a motion that starts with the heel of the knife on the stone and ends with the point of the knife. The motion should resemble a sweeping arc pattern across your stone. Be very careful to maintain the angle of the knife on the stone. Longer curved knives provide additional challenges but as long as you can maintain the angle you will be sharpening very effectively. Repeat this process on the other side of the knife and continue repeating until you have sharpened your knife though all your stone grits.
I can personally verify that this will get your knives very sharp. I will spare you all the gory details, but the picture is of the instructions the ER sent me home with after stopping the bleeding and patching me up. I have to say, that’s not what I had in mind regarding “Thanksgiving tips”. So: not only will knives slide easily through spinach, but they will go through finger and fingernail like a hot knife through butter after being sharpened by this whetstone. Very clean, straight cut. Impressive, really. Just take it slow and don’t be a moron like me.
Actually, the company contacted me to make sure I received the stones and that I was happy with them. Excellent service. The stones are great! I'm pretty much a novice so the clear instructions that came with the stones and the eBook instructions were wonderful. The eBook had quality pictures demonstrating the use of the stones and the written instructions were clear and to the point. Within minutes of opening the box I had the stones figured out and sharpening my AF survival knife, my pocket knife and a couple of my wife's kitchen knives...which included a very expensive chef's knife. Very satisfied with this product and highly recommend it.
An important but often confusing area of sharpening is knowing when you're done with one stone and ready for the next finer grit. On coarse stones it is very easy. When you sharpen one side you will notice a burr forming on the opposite side of the edge. This burr is hard to see but is easy to feel. Very carefully feel for the burr by gently running your hand from the spine to the edge. (Do not run your finger along the knife edge from heel to tip, that's only asking for trouble!) A burr is formed when your stone removes material directly at the edge. The burr will move from one side of your knife to another as you alternate sharpening sides. Make sure you have felt the burr jump between both sides before you move on to the next finer stone. That will ensure that you have sharpened both sides effectively. The finer grits are done the same way but the burr is much smaller. On the finest grits you may not be able to notice the burr at all. Testing the knife sharpness will tell you when you're done. (Learn how you can test to see if your knife is sharp.)
If your knife is dull, we advise you to start with the diamond stone. After restoring the edge to original shape, de-burr the edge lightly with the ceramic stone in order to get a razor-sharp edge. Use no oil or water. Start by laying the blade flat on the stone, raise the blade spine approx. the thickness of the blade, and start moving the knife in circular motions.
Be careful: Don’t move your fingers laterally along the edge, you’ll cut yourself. Feel for a rough area running from tip to heel. Again, it takes time to know what to expect because the best burr will be subtle. Just know that the bigger the burr, the more metal you are removing—more than necessary. Don’t worry, you won’t ruin the knife doing this. You’re learning here, and mistakes are part of the sharpening journey. Learn from them.
A blade's sharpness may be tested by checking if it "bites"—begins to cut by being drawn across an object without pressure. Specialized sticks exist to check bite, though one can also use a soft ballpoint pen, such as the common white Bic Stic. A thumbnail may be used at the risk of a cut, or the edge of a sheet of paper. For kitchen knives, various vegetables may be used to check bite, notably carrots, tomatoes, or cucumbers. In testing in this way, any nicks are felt as obstacles.
My first set of sharpening stones so I have nothing to compare them to. For $50, though, great price to get into the world of sharpening. Stones are great and easy to use. Was able to put hair shaving edges on knives. Took a couple of knives to feel comfortable and better with the process and how to sharpen, but the stones you get work great. Here's the secret though. Get the green leather stoping block as well. As great as the stone are, I have found that stroping the knife after the fact is what really brings out that razor edge. And after using the knife, stroping it again, will restore and keep it razor sharp. Hope you enjoy it as much as I am.