Unfortunately, the arrays of modern whetstone can be bewildering to the inexperienced sharpeners that so often times many of them end up with a crap or wrong decision on stone type for their utensils. The most difficult to determine is whether the whetstone is fake or fabricated with low quality of materials. To avoid this you can only go for the reliable brand of a whetstone.
One thing about this stone is that it is very "thirsty." I had a cup of water close by just to add a little water periodically when it felt like it was scraping a little too aggressively. Also, be sure to do as the instructions say and use different parts of the sharpening surface. I wasn't paying attention the first few minutes, and apparently I would end each sharpening pass in the exact same spot, creating a very very small notch on the edge of the stone. So I turned the stone around and made sure to vary the ending spot, and it seemed to buff out that little notch very quickly. My knife is now incredibly sharp--it seems to glide through material rather than "cut" it. I know some people would continue to go even higher with the grit, but for my purposes this whetstone is just perfect. I'll be tackling the kitchen knives next!
I can personally verify that this will get your knives very sharp. I will spare you all the gory details, but the picture is of the instructions the ER sent me home with after stopping the bleeding and patching me up. I have to say, that’s not what I had in mind regarding “Thanksgiving tips”. So: not only will knives slide easily through spinach, but they will go through finger and fingernail like a hot knife through butter after being sharpened by this whetstone. Very clean, straight cut. Impressive, really. Just take it slow and don’t be a moron like me.
Very handsome and functional. The leather that makes up the necklace is high quality and the knot they use is seldom seen. I was able to touch up my bark River gunny sidekick with it( m4 steel at 62-64 hrc!), And that is saying something. Haven't tested the fish hook groove, because I don't generally fish in the winter, but I'm looking forward to trying it out
Made from hand-selected A36 hot rolled steel that is left untreated to allow it to age naturally and beautifully from season to season, Stahl's new X firepit will be a center of warmth and attention for generations. Each minimalist firepit is made in Portland, Oregon and includes four 3/16 inch steel pieces that can be assembled in minutes with no complicated parts or screws.
High Grit Stones: These are also known as finishing stones with the number range going up to 8000, and give you a super refined edge.  They work great with Western knives as they cutting edge resembles a “U” as opposed to a “V”. If you are using your knife to cut meat, then you can happily stop at 4000 or 6000 grit. If you are only using it for vegetables or fruit go all the way to the 8000.
Pressure is something that is sometimes not mentioned but in my experience and in my opinion, it is extremely important to apply the correct amount of pressure, I use three different levels of sharpening pressure, with my sharpening pressure being measured on a scale from 1-5 with 1 being very light and 5 being maximum pressure. When you initiate the sharpening process, when you have all your ducks lined up and you are ready to start, use P4 (Pressure at level 4, almost maximum). in this case it is you and the stone working together, you are going to apply pressure with your finger tips (2 or 3 finger tips) placed as close to the primary edge as you can get, i.e. over the area you are working on, on the opposite side of the blade. As you push the knife away from you in a trailing motion, apply P4 pressure to the knife as it glides over the wet whetstone, (whet means sharpen) you will see the black residue start to form in the water on the surface, this is Swarf and this is good, don’t feel obliged to remove this with water, it is fine. Continue working from the heel to the tip of the knife moving your fingers along the edge and applying pressure as you move the knife away from you on the right side of the knife and as you pull it towards you on the left side, these are called edge trailing strokes.

An extremely well written and informative article on sharpening. Overtime we all get to love certain stones for our sharpening needs. I am a huge coticule fan, and although i have used all the others, i always come back to this natural stone above all others. Still trying to figure if i chose it or it chose me! NEver the less there are so many options out there it is not hard with a little time and effort to find the right combination for your needs.


Cutting angle – With a manual stick or sharpening stone you set the angle yourself so this does not factor into the equation when choosing that type of sharpener. When shopping for an electric sharpener however it does. You’ll want to decide if you want your knives to have the 15 degree “Asian” style angle so that you can make precise cuts or the Western standard 20 degrees or 22-degree sharpening angle. Most people will opt for the 20 or 22-degree angle simply because their cuisine doesn’t call for a lot of finesse from their knives and those knives are probably of a heavier Western variety anyway.

Our large selection of stones from many well-known manufacturers will allow connoisseurs to find the ideal stone for their needs. Because all manufacturers formulate their stones to emphasize a different mix of qualities, and because these qualities can vary widely between different stones, most woodworkers choose stones from several manufacturers to build up an optimal set of sharpening stones. Then again, once you get to know the characteristics of certain types of stone, you may find one supplier who will provide all the stones you need. Sometimes this can be an advantage. But there is no one size that fits all; each stone must fit your needs and work style.
×