You will be given access to our useful online learning material: a set of videos and articles to help you improve your sharpening technique. These resources were made by professional knife sharpeners, specifically for beginners and intermediate sharpeners. The articles and videos will guide you and teach you knife sharpening from scratch, also covering more advanced techniques. You can also get in touch with us anytime if you have any questions concerning sharpening specific types knives.

"Sharpening is like a hangover cure," says Laurie Timpson, founder of Savernake Knives in Wiltshire. "If there was a cure and you knew about it, I'd stay at your house, crash on your sofa and have whatever it was when I woke up. Everyone would have it and there'd be no discussion. Everybody says they've created a perfect sharpening technique, and they haven't." 
Your stroke can be straight or circular, from "hilt to tip" OR "tip to hilt," whichever is more comfortable. If you're using a small portable sharpener, stroke the blade in nearly a straight direction. Remember to always cut into the stone and never pull or drag your edge backwards. The blade edge should face in the same direction as your stroke. So, you're essentially moving the metal away from the edge. We recommend the circular stroke as it helps you maintain your angle instead of having to find it every time you lift the knife from the stone.
Pressure is something that is sometimes not mentioned but in my experience and in my opinion, it is extremely important to apply the correct amount of pressure, I use three different levels of sharpening pressure, with my sharpening pressure being measured on a scale from 1-5 with 1 being very light and 5 being maximum pressure. When you initiate the sharpening process, when you have all your ducks lined up and you are ready to start, use P4 (Pressure at level 4, almost maximum). in this case it is you and the stone working together, you are going to apply pressure with your finger tips (2 or 3 finger tips) placed as close to the primary edge as you can get, i.e. over the area you are working on, on the opposite side of the blade. As you push the knife away from you in a trailing motion, apply P4 pressure to the knife as it glides over the wet whetstone, (whet means sharpen) you will see the black residue start to form in the water on the surface, this is Swarf and this is good, don’t feel obliged to remove this with water, it is fine. Continue working from the heel to the tip of the knife moving your fingers along the edge and applying pressure as you move the knife away from you on the right side of the knife and as you pull it towards you on the left side, these are called edge trailing strokes.

Cut a wine cork so that it measures .5 of an inch and use that as your visual guide. You can keep it at the end of your water stone and rest the spine of the knife on it so that you can see what that angle looks like. Now this is all pretty nifty but you still have to learn to move that knife over the water stone holding it at that angle, whether you chose 20 or 15 deg, making the template is the easy part, stabilizing that angle is where practice is crucial. You can hold the knife with that wine cork in place and that is the angle you want sharpen at but now that piece of cork has to go, you’re on your own. I have taught many many people to sharpen a knife and believe me, this particular part of the process is not as hard as many people believe! In fact as you start actually sharpening the knife you will become quite motivated to succeed because it isn’t as hard as you thought it would be. In time, you’ll learn that you don’t need or want to sharpen everything at 20 deg, but for the sake of building muscle memory it is a good place to start.
I enjoy these stones so much that the feedback is not a deterrent at all for me, I don’t even think about it. The results are always nothing but top notch, they deliver exactly what I want, some of the sharpest knives I have ever produced were sharpened on Shapton Glass stones. They may be thinner but they last a very long time, they are easy to maintain as well,
To summarize, Shapton Glass 500, 1,000 and 2,000 is a good combination and if you would like to throw in the 4,000 grit stone in lieu of the 2,000 that is good as well. If your knives are very hard, ZDP 189 for example, this is a fantastic choice. (They are also excellent for tools, chisels etc. and they are the premier choice for many Straight Razor honers).

Oil Stones differ from water stones in that they require the use of honing oil to float the swarf (metal particles). Also, these stones are commonly made from one of three different materials consisting of Novaculite, Aluminum Oxide (Corundum), or Silicon Carbide (Carborundum) and they all use oil to lubricate the stone and suspend the swarf in order to prevent the stone from becoming clogged. Also, while Novaculite and Coticule are the most traditional types of oil stones, there are also synthetic oil stones made by the Norton abrasives company called “India Oil Stones”.
I would say they are worth the money. Go for it. I took a blunted Pampered Chef kitchen knife from completely dull to razor sharp in about an hour (of bumbling and repairing mistakes LOL) heavy grinding. If you have a severely damaged blade, grab one of those cheesey two sided stones from Harbor Freight to do your heavy grinding. From there these stones will work very well.
As you see in the pictures, it is always very important to keep same angle of about 10' to 15', which is about two coins height between the blade and the whetstone. Gently push the point you want to sharpen with your first, second and third fingers. While keeping the angle and pushing the point with your fingers, stroke the blade until it reaches the other edge of the whetstone. Then pull the blade back until it reaches the edge of the whetstone. This back and forth is counted as one stroke. Repeat it for about five strokes until you can see or feel some small burrs (edge curvatures). Then move the position of your fingers to where you have not sharpened yet, and repeat this five strokes of sharpening processed from the tip to the base of the blade.
Place an old coffee mug upside down so that the bottom of the mug is exposed to the air. In a pinch, a coffee mug can serve as a surprisingly effective sharpening tool if you don't have any fancy equipment. The ceramic material of a mug is a material coarse enough to get good results. Indeed, some honing rods even use ceramic material to keep a blade homed in between sharpenings.
Let’s talk about the tip of the knife, the burr needs to be formed here as well. Here is a simple trick that works, I like keeping things simple. As you get to the tip area of the knife, the front inch, raise your elbow so that it is parallel to the ground, you can also raise your sharpening angle very slightly but just raising your elbow will perform wonders and likely eliminate the tip sharpening area issue, it is an issue for some.
Aluminum-Oxide oil stones are very popular man-made sharpening stones produced by an abrasives company called Norton and which are commonly called India Stones. Generally less expensive than Arkansas stones (aka Novaculite), these stones are graded coarse, medium, and fine and are designed for fast cutting. Yet, when the fine grit is used, they can also produce a relatively fine edge. Also, because India Oil Stones are both softer and coarser than Arkansas Stones, they are commonly used in conjunction with Novaculite to cut the initial edge bevels or, repair extremely dull or damaged edges before refining and polishing the bevel with an Arkansas Stone.

A: Another issue that comes up with electric knife sharpeners is how to clean them. Or if, in fact, they actually need cleaning at all. The answer to the second question is that yes, they do need to be cleaned occasionally. And by occasionally we mean once a year or so if you use them with any frequency. Obviously if you’ve only used the sharpener a few times then there’s no compelling reason to clean it, other than just wanting to keep things tidy (and there’s nothing wrong with that). So, having established that sharpeners do need to be cleaned occasionally you need to know how to do so in a safe and effective manner. It’s not complicated.
I do have to question the grit ratings of these stones. I didn't notice anything before using them, but after a day, the 2000 grit actually felt courser than the 1000 grit side of the other stone. Whether that could be a byproduct of other factors or an indication of the more obvious, being that the grit ratings aren't accurate, I don't know. But that seemed to be the main criticism of cheaper whetstones, that their grit ratings often aren't accurate. Or maybe it's less a problem with accuracy and more a difference that most synthetic stones might have in common when being compared to much pricier natural stones?
if you have regular kitchen knives it will not work- first its to deep and the blade does not stick out, not dinner knives but cooking knives. of all the knives i put in it only 1 was wide enough to stick out. the device does not hold the blades. all the blades tested fell out of it, even a hunting knife, maybe its for 1 type of knife and they are selling it as the must have tool for all.. that said sell something useless for a few bucks that most cant use, they got a few bucks that most will blow off and not worry about a refund.. DONT WASTE YOUR MONEY.
Manufacturer contacted and sent a new one for replacement. Great customer service but replacement item was nicked on the corner. It was still usable so i didn't bother to ask for another replacement. I would recommend item to be shipped in another box instead of an over-sized yellow envelop which is not adequate protection. Item sharpen my knife pretty good though..
Choose the style of stone. You'll need to choose a natural or synthetic stone that can be used wet (soaked in water), with oil, or dry. There are also diamond stones that are actually very small diamonds attached to a metal surface. Stones that are soaked in water are softer stones which means you can quickly sharpen your knives. Unfortunately, these stones will wear down faster than the others. Oil stones are the least expensive and they're made of a harder material.[2]
Whetstone has two different sides of grain for sharpening and polishing knife edges. These softer Japanese stones have several advantages over harder stones. Because they are softer, they do not become glazed or loaded with detritus. Plus, they are lubricated effectively with water rather than oil, but can be used with either. Submerge the stone in water for about 5 - 10 minutes. Continue to apply water while sharpening with the Whetstone Cutlery Two sided Whetstone Sharpening Stone. The stone releases small particles during the sharpening process; this powder in combination with water allows the sharpening. After a while you will notice a small burr at the edge. Now repeat the same process on the other side of the blade. Finally, turn the stone over and repeat the procedure, this time using the finer grit of the stone. In order to remove the remaining burr, pull the blade at an angle over the stone. Rinse the stone and clean off the grinding residue. Clean your knife with hot water.
Best purchase I every made. while my knife doesnt cut a fine layer of tomato without touching it, it became as good as it was when I purchased. I recommend users to learn how to properly sharpen the knife. It took me about 30 minutes to sharpen a single knife to what it is today. The knife gets really sharp. Also, with use, the surface gets uneven. I recommend you draw a grid in pencil and then file using the grinder stone until the grids disappear. This ensures the surface remains flat during all use.
It looks like it can be a Sci-Fi film prop. This is a 2 stage type of sharpening system. You'll get a non slip cushion with it which is at the bottom offering stability for the user. It's ergonomic handle provides a comfortable and easy grip. This cushion offers the stability needed when sharpening and polishing your pocket knife to it's absolute razor sharpness. The sharpener does the work as you hold down the grip and simply place your pocket knife to get sharpened by the motions of the ceramic and diamond sharpener wheels. Simply run your dull knives through the device and you'll get the results you've been looking for. This one will definitely help you when you learn how to sharpen a pocket knife on the Priority Chef.