Unfortunately, the arrays of modern whetstone can be bewildering to the inexperienced sharpeners that so often times many of them end up with a crap or wrong decision on stone type for their utensils. The most difficult to determine is whether the whetstone is fake or fabricated with low quality of materials. To avoid this you can only go for the reliable brand of a whetstone.
However, because the Belgian Blue stone generally occurs in relatively wide columns with much thinner layers of Vielsalm Coticule on either side adjacent to the slate, the Belgian Blue stone is more plentiful that Coticule and thus, it’s somewhat less expensive. But, it’s also somewhat softer than Coticule and is not divided into different grades as Coticule is. Furthermore, because it is a softer stone than Coticule, it is sold without a substrate layer.
An extremely well written and informative article on sharpening. Overtime we all get to love certain stones for our sharpening needs. I am a huge coticule fan, and although i have used all the others, i always come back to this natural stone above all others. Still trying to figure if i chose it or it chose me! NEver the less there are so many options out there it is not hard with a little time and effort to find the right combination for your needs.
Meanwhile, if you want something that you can use to sharpen a variety of knives and edges, including small and pointed tools, you might want to consider the DMT WM8CX-WB 8-Inch Duo Sharp Plus Bench Stone – Coarse/Extra Coarse with Base. For less than a hundred bucks, you can even use it to repair a damaged edge because of its extra-coarse diamonds.
Practice holding the knife at a 20 degree angle. Most straight blades need to be sharpened at a 20 degree angle. To find the angle, hold the directly in front of you so it's straight up and down. This is 90 degrees. Tilt the knife halfway towards the table so it's at a 45 degree angle. Tilt the knife halfway again so it's about an inch (2.5 cm) above the table. This should be a 20 degree angle.
Your stroke can be straight or circular, from "hilt to tip" OR "tip to hilt," whichever is more comfortable. If you're using a small portable sharpener, stroke the blade in nearly a straight direction. Remember to always cut into the stone and never pull or drag your edge backwards. The blade edge should face in the same direction as your stroke. So, you're essentially moving the metal away from the edge. We recommend the circular stroke as it helps you maintain your angle instead of having to find it every time you lift the knife from the stone.
In summary: Peter Nowlan is a professional knife sharpener based in Halifax (Canada) and he recommends the KnifePlanet Sharpening Stone Set, a beginners and intermediate kit that includes 4 sharpening grits: 400/1000, 3000/8000, a bamboo base and the KnifePlanet Flattening Stone. The Japanese Naniwa 3-stone combination is also a great (and more expensive) choice, ideal for professionals and more advanced sharpeners: the Naniwa stones are slightly bigger compared to KnifePlanet’s. In both cases, a coarse, medium and fine grit combination is very effective to sharpen and refine the edge:
The Juuma sharpening and honing stones offer a simplified working principle while at the same time ensuring the highest possible quality in the offered grits. Juuma Cobalt Blue stones are made of an aluminium oxide and a bonding agent. Adding cobalt serves to slow stone abrasion and increase the speed of sharpening. The speed bonus is especially marked when stoning blue steel (blue paper steel that is often used for Japanese planes and chisels). The cobalt gives the stones their blue colour. Juuma is our proprietary brand. Juuma sharpening stones are produced by a renowned Japanese whetstone manufacturer.
I purchased this set together with the 400/1000 grit stone assuming that some of my knives were quite dull and would need work on a coarse grit stone. Premium Whetstone Sharpening Stone 2 Side Grit 400/1000 | Knife Sharpener Waterstone with NonSlip Rubber Base & Flattening Stone. This is my first wetstone. First off I tried to sharpen my Chicago Cutlery boning knife. This knife is nearly thirty years old, has been abused in may ways and was quite dull. It was very difficult for me to get a burr on this blade, which I attribute to poor technique. Next I moved on to my Henckels Professional S paring and chef's knives. The paring knife was moderately sharp and was modestly improved after working over all three grits of stone. It would cut paper but again it was difficult to develop a burr with this blade. Undaunted I switched to the chef's knife. This knife is twenty years old and has never been professionally re-sharpened. I have sharpened it twice with a Lanksey sharpening system which marred the finish but did put a good edge on the blade. Lansky Standard Coarse Sharpening System with Fine Hones. The chef's knife was moderately dull and had several pits visible on the cutting surface. I modified my technique for passing the knife over the stone and worked the chef's knife over the 400 grit stone aggressively and eventually I was able to get a burr to form from the tip of the knife all the way to the handle. From there it was a simple process of reforming the burr on the 1000 grit stone and then finishing on the 6000. After sharpening, the chef's knife easily and cleanly slices a tomato with very light pressure and is in my opinion very sharp. Not sushi knife sharp but more than enough for the chopping and slicing I expect of it. I'm looking forward to going back and working both the boning knife and the paring knife over again. Don't expect a good result from this product the first time you use it. Watch videos on using a wetstone, expect to spend at least twenty minutes per knife at first, and practice forming a burr. If you can form a burr, you will be able to successfully sharpen your knife.