Removing the burr is fairly simple. You'll need a leather strop or block (this sort of thing), which is designed to catch the metal fibres from the knife. You could do it with a fibrous tea towel or some newspaper if you like, but I'd suggest going with leather to begin with. The motion is fairly similar to sharpening. Draw the knife over the leather, going away from the edge at roughly the same angle as when you sharpened.
One more thing to consider before you proceed is if you would like to sharpen your knife freehand or use a guide such as the DMT Sharpening Guide. Your skill and experience in sharpening will help you decide on the method that's best for you. If you are experienced and comfortable with freehand sharpening, a knife guide may be unnecessary. On the other hand, a knife sharpening guide is an inexpensive and easy way to keep the angle consistent. If you have tried to sharpen before but never achieved the proper edge, we recommend using the sharpening guide. The guide can solve common mistakes in the sharpening process. If you choose to use a guide, please read our how-to for using the knife sharpening guide.
Steeling helps maintain sharpness. This process realigns the edge, correcting for dulling causes such as a rolled edge. A sharpening steel is a type of hardened cylindrical rod used similarly to honing stones. For example, a butcher steel is a round file with the teeth running the long way, while a packer steel (used in the meat packer's industry) is a smooth, polished steel rod designed for straightening the turned edge of a knife, and is also useful for burnishing a newly finished edge. Because steels have a small diameter they exert high local pressure, and therefore affect the knife metal when used with very little force. They are intended for mild steel knives that are steeled several times a day, but are not well suited for today's tougher and harder blade steels. Diamond steels are now available that have an industrial diamond coating and can remove blade metal as well as straighten, therefore used correctly they can re-profile a knife instead of just honing.
Choose the style of stone. You'll need to choose a natural or synthetic stone that can be used wet (soaked in water), with oil, or dry. There are also diamond stones that are actually very small diamonds attached to a metal surface. Stones that are soaked in water are softer stones which means you can quickly sharpen your knives. Unfortunately, these stones will wear down faster than the others. Oil stones are the least expensive and they're made of a harder material.
All rights reserved. WARNING - Under the Liquor Control Reform Act 1998 it is an offence to supply alcohol to a person under the age of 18 years (Penalty Exceeds $17000). It is an offence for a person under the age of 18 years to purchase or receive liquor (Penalty exceeds $700). This web site is operated by Chef’s Armoury. ABN 62 001 477 014. Liquor Licence 36129161.
Practice holding the knife at a 20 degree angle. Most straight blades need to be sharpened at a 20 degree angle. To find the angle, hold the directly in front of you so it's straight up and down. This is 90 degrees. Tilt the knife halfway towards the table so it's at a 45 degree angle. Tilt the knife halfway again so it's about an inch (2.5 cm) above the table. This should be a 20 degree angle.
Clamp-style sharpening tools use a clamp with several holes with predefined angles. The stone is mounted on a rod and is pulled through these holes, so that the angle remains consistent. Another system is the crock stick setup, where two sticks are put into a plastic or wooden base to form a V shape. When the knife is pulled up the V, the angle is held so long as the blade is held perpendicular to the base. Several cutlery manufacturers now offer electric knife sharpeners with multiple stages with at least one grinding stage. These electric sharpeners are typically used in the kitchen but have the ability to sharpen blades such as pocket or tactical knives. The main benefit of using an electric sharpener is speed with many models that can complete the sharpening process in one to two minutes. The disadvantage is that the sharpening angle is fixed so some specialized knives, like a Japanese style Santoku, may need additional attention to sharpen to the ideal angle.
The word “Novaculite” is derived from the Latin word “novacula”, which means “razor stone” and is essentially a metamorphic, recrystallized, variety of Chert composed mostly of microcrystalline quartz that is found in the found in the Ouachita Mountains of Arkansas and Oklahoma and in the Marathon Uplift of Deposited in the Devonian Period and the early Mississippian Subperiod some 410 to 325 million years ago and subjected to uplift and folding during the Ouachita orogeny of the Atokan Epoch (early Pennsylvanian Subperiod), Novaculite is a very tough stone that is resistant to erosion and thus, the various layers of Novaculite stand out as ridges in the Ouachita Mountains. Thus, due to both its availability and its composition, it has been mined since ancient times for use as arrowheads and spear heads as well as in more modern times for use as sharpening stones.
JapaneseChefsKnife.Com (JCK, Established in 2003) is the direct internet sales division of The Kencrest Corporation. We supply a wide range of top quality Japanese Chef's knives at lower than Japanese Retail Prices direct from Seki City; the Japanese cutlery capital where fine knives are produced using over 800 years of Samurai sword-making tradition and history.
Historically, there are three broad grades of Japanese sharpening stones: the ara-to, or "rough stone", the naka-to or "middle/medium stone" and the shiage-to or "finishing stone". There is a fourth type of stone, the nagura, which is not used directly. Rather, it is used to form a cutting slurry on the shiage-to, which is often too hard to create the necessary slurry. Converting these names to absolute grit size is difficult as the classes are broad and natural stones have no inherent "grit number". As an indication, ara-to is probably (using a non-Japanese system of grading grit size) 500–1000 grit. The naka-to is probably 3000–5000 grit and the shiage-to is likely 7000–10000 grit. Current synthetic grit values range from extremely coarse, such as 120 grit, through extremely fine, such as 30,000 grit (less than half a micrometer abrasive particle size).
I really like this stone. The 1000/4000 grit combination is perfect for my needs. I'm a woodturner, and belong to a club that brings in professional turners from around the world. One had an eye opening test of sharpness. He stacked around 25 new razor blades in a box with one open side. The box assured that the blades were in perfect alignment. If you looked at the blades' sharp ends head on, all you saw was black. His point was that if you can see the edge, the blade is not sharp. Any reflection from the edge, again, facing it head on, is a dull spot. My long story leads to the fact that I was able to sharpen several knives to the point of not seeing the edge. This is not the stone to use if you are trying to remove nicks from a blade. A lower grit will do that job. This is for putting a fine, "invisible" edge on the blade, and with the right technique, that's what it will do. Another thing to consider is the fact that these stones are "sacrificial" A stone wears because it is deliberately giving up dull surface particles to expose the sharp ones below them. Anyone expecting a stone to last forever is mistaken. Bottom line? I think this is a great stone that takes my knives to the level of sharpness I need in both woodworking and cooking. I also like the rubber frame it sits in, giving you much better control over the stone. Your efforts can go into sharpening without having to steady the stone on your workbench or countertop.
Just keep at it and concentrate, visualize that edge and bevel as you sharpen and keep in mind what you are trying to achieve. You need to do this on both sides, for me, I found that the hardest part, getting the other side of the knife to match the side I started on. I start on the right side of the blade at the tip and work my way towards the heel. When I do the “back” of the knife, I start at the heel and work towards the tip.
It helps you get the knack for a consistently correct angle BUT the idea falls apart a bit when it comes to the curve and taper part of the knife and if your knife has an excessively narrow (slicer/boner) or wide (cleaver) width. It will also mark up the sides of your knife which may bother some who are obsessed with the cosmetic appearance of their $150+ Japanese knives--I could care less.
Both Belgian Blue and Vielsalm Coticule are ancient stone layers found in the Belgian Ardenne Mountains with characteristics similar to both Novaculite and Siliciclastic sedimentary stone in that it is a metamorphic stone consisting of both gray and yellow volcanic ash mixed with tiny Spessartite Garnet crystals suspended in a clay matrix. However, due to its geology, both types of stone occur only in vertical seams sandwiched between two thick layers of bluish-purple slate and thus, they must be meticulously extracted mostly by hand. However, this type of extraction process is both very time-consuming and very labor-intensive and, quarrymen can only extract the stone for a few months each year due to inclement weather conditions. Consequently, both Belgium Blue and Coticule whetstones tend to be somewhat expensive.
Diamond hones are made from very small, industrial grade, diamonds adhered to the face of a metal or plastic plate. Also, because Diamonds are so much harder than any of the other sharpening materials, they tend to cut very fast and last much longer than the other whetstone materials. But, they are also often more expensive to purchase. In addition, Diamond Stones generally consist of three different styles consisting of a solid metal plate coated with an adhesive and diamond dust with holes in the plate to allow the swarf to escape, a solid plate without holes for sharpening tools with corners that might catch in the holes, and a plastic plate with islands of exposed plastic interspersed with the adhesive and diamond dust to act as a lubricant.
With its premium series Select II, the whetstone manufacturer Sigma Power Corporation from Tokyo addresses users of high-alloy steels such as HSS. These stones, too, are obviously intended to engender a grinding experience similar to that of natural stones. The special production process is expensive, but the Sigma Select II probably has no equal when it comes to demolishing steel.
You will be given access to our useful online learning material: a set of videos and articles to help you improve your sharpening technique. These resources were made by professional knife sharpeners, specifically for beginners and intermediate sharpeners. The articles and videos will guide you and teach you knife sharpening from scratch, also covering more advanced techniques. You can also get in touch with us anytime if you have any questions concerning sharpening specific types knives.