I purchased this set together with the 400/1000 grit stone assuming that some of my knives were quite dull and would need work on a coarse grit stone. Premium Whetstone Sharpening Stone 2 Side Grit 400/1000 | Knife Sharpener Waterstone with NonSlip Rubber Base & Flattening Stone. This is my first wetstone. First off I tried to sharpen my Chicago Cutlery boning knife. This knife is nearly thirty years old, has been abused in may ways and was quite dull. It was very difficult for me to get a burr on this blade, which I attribute to poor technique. Next I moved on to my Henckels Professional S paring and chef's knives. The paring knife was moderately sharp and was modestly improved after working over all three grits of stone. It would cut paper but again it was difficult to develop a burr with this blade. Undaunted I switched to the chef's knife. This knife is twenty years old and has never been professionally re-sharpened. I have sharpened it twice with a Lanksey sharpening system which marred the finish but did put a good edge on the blade. Lansky Standard Coarse Sharpening System with Fine Hones. The chef's knife was moderately dull and had several pits visible on the cutting surface. I modified my technique for passing the knife over the stone and worked the chef's knife over the 400 grit stone aggressively and eventually I was able to get a burr to form from the tip of the knife all the way to the handle. From there it was a simple process of reforming the burr on the 1000 grit stone and then finishing on the 6000. After sharpening, the chef's knife easily and cleanly slices a tomato with very light pressure and is in my opinion very sharp. Not sushi knife sharp but more than enough for the chopping and slicing I expect of it. I'm looking forward to going back and working both the boning knife and the paring knife over again. Don't expect a good result from this product the first time you use it. Watch videos on using a wetstone, expect to spend at least twenty minutes per knife at first, and practice forming a burr. If you can form a burr, you will be able to successfully sharpen your knife.
Keep the stone submerged until the bubbles slow down or about 5 minutes then it's ready for use. Starting with the lowest grit which is 1000 on this stone, hold your knife at about a 15 degree angle and slide it away from you. It only takes light pressure along the strokes. You don’t need to push too hard. Gently slide from the tip to the base of the blade. After about 12 to 15 strokes, flip the blade over and repeat on the other side. Continue using gentle and even passes across the stone. Remember to hold the blade at about a 15 degree angle which is about half the height of your thumb. Keep the moves consistent and at the same speed.

Diamond sharpening stone delivers fast cutting and sharp edges. They are tougher in material and doesn’t flatten. Therefore, it is the best way on investment if you want such of the sharpener that easy to maintain and practical to use. Diamond sharpening stone doesn’t require water other than a spill. It is also applicable to use with lubrication if you wish to.
The stones from Shapton are probably the hardest of all Japanese sharpening stones. They will remain flat for a long time. They are therefore the best choice if you are looking for a relatively coarse stone that cuts quickly without having to be dressed repeatedly. The finer-grained stones also work very well. But Shapton stones do not provide the mirror finish you can achieve with softer stones.
You want sharpening stones that will be useful for the majority of your edges now, and that will remain useful as you expand both your tools and your sharpening toolkit in the future. Ending up with duplicate stones or ones that are no longer useful as you gain new knives or tools is a waste of money. The goal is to start with something that will stay with you as your needs develop.
Next we sharpen the opposite side of the blade. Just as you did before, sharpen the knife keeping an angle of 10' to 15'. Push the point you want to sharpen with your first, second and third fingers. While keeping the angle and pushing the point with your fingers, stroke the blade until it reaches the other edge of the whetstone. Then pull the blade back until it reaches the edge of the whetstone. This back and forth is counted as one stroke. Repeat it for about five strokes until you can see or feel some small burrs (edge curvatures).. Then move the position of your fingers to where you have not sharpened yet, and repeat this five strokes of sharpening processed from the tip to the base of the blade. When your whetstone becomes dry, occational watering during  sharpening process will also help and improve smooth sharpening.
Today, however, there is a whole new generation of mechanical sharpeners that are far more forgiving for those who may not use perfect technique. At the same time many more people have become accustomed to sharpening their knives this way and the average novice of 10 years ago is now the seasoned pro. It is still possible to damage knives with an electric sharpener, but you would have to either be trying to damage the knife or have some type of accident in order to do so.

I purchased this set together with the 400/1000 grit stone assuming that some of my knives were quite dull and would need work on a coarse grit stone. Premium Whetstone Sharpening Stone 2 Side Grit 400/1000 | Knife Sharpener Waterstone with NonSlip Rubber Base & Flattening Stone. This is my first wetstone. First off I tried to sharpen my Chicago Cutlery boning knife. This knife is nearly thirty years old, has been abused in may ways and was quite dull. It was very difficult for me to get a burr on this blade, which I attribute to poor technique. Next I moved on to my Henckels Professional S paring and chef's knives. The paring knife was moderately sharp and was modestly improved after working over all three grits of stone. It would cut paper but again it was difficult to develop a burr with this blade. Undaunted I switched to the chef's knife. This knife is twenty years old and has never been professionally re-sharpened. I have sharpened it twice with a Lanksey sharpening system which marred the finish but did put a good edge on the blade. Lansky Standard Coarse Sharpening System with Fine Hones. The chef's knife was moderately dull and had several pits visible on the cutting surface. I modified my technique for passing the knife over the stone and worked the chef's knife over the 400 grit stone aggressively and eventually I was able to get a burr to form from the tip of the knife all the way to the handle. From there it was a simple process of reforming the burr on the 1000 grit stone and then finishing on the 6000. After sharpening, the chef's knife easily and cleanly slices a tomato with very light pressure and is in my opinion very sharp. Not sushi knife sharp but more than enough for the chopping and slicing I expect of it. I'm looking forward to going back and working both the boning knife and the paring knife over again. Don't expect a good result from this product the first time you use it. Watch videos on using a wetstone, expect to spend at least twenty minutes per knife at first, and practice forming a burr. If you can form a burr, you will be able to successfully sharpen your knife.

×