To use Al's method, take a black felt pen and shade in the bevel of the knife. Then take two strokes on the stone and examine the edge. If you have maintained the proper angle then all the black will be gone. If you see black on the top of the edge it means you are holding the back of the knife too far from the stone. If there is black on the bottom of the edge but the top is clean then you are laying the knife too flat on the stone and you need to raise it a bit. Repaint the edge and try it again. Once you discover what the right angle looks like then just maintain that.
Table mounted device – Typically the manual powered table mounted sharpener looks virtually identical to the electric powered sharpener with a slot for each stage. Where they differ is that each slot in the manual powered sharpener has only one groove and you pull the blade through this groove toward you to sharpen the blade. Once the blade is sufficiently sharp you place it in the honing groove to refine the edge and pull it toward you again several times. If there is a third, cleaning, stage you repeat the process for that stage as well.
I am just starting out sharpening with whet stones. I have found these stones to be very nice and the instructional videos that come along with the set on knifeplanet are extremely helpful to anyone starting out. The cost of the set was very reasonable and seems to be a great value. The customer service is amazing, I lost the site for the videos and sent an email to get the information and immediately there was a reply with all of the links that I needed. I appreciate their attention to their customers!!
I would say they are worth the money. Go for it. I took a blunted Pampered Chef kitchen knife from completely dull to razor sharp in about an hour (of bumbling and repairing mistakes LOL) heavy grinding. If you have a severely damaged blade, grab one of those cheesey two sided stones from Harbor Freight to do your heavy grinding. From there these stones will work very well.
The stones from Shapton are probably the hardest of all Japanese sharpening stones. They will remain flat for a long time. They are therefore the best choice if you are looking for a relatively coarse stone that cuts quickly without having to be dressed repeatedly. The finer-grained stones also work very well. But Shapton stones do not provide the mirror finish you can achieve with softer stones.
"How do I use this daunting metal rod?" I hear you ask. Well, it's not too hard, really. The best way for a beginner is to balance the steel on a surface with the tip secured by a damp tea towel. You want to get that angle right, whether it's around 15 degrees for a Japanese knife or 20 degrees on a German or French blade. Then swipe slowly down, away from you, making sure the whole blade is honed – around five swipes on each side should do. 
I purchased this set together with the 400/1000 grit stone assuming that some of my knives were quite dull and would need work on a coarse grit stone. Premium Whetstone Sharpening Stone 2 Side Grit 400/1000 | Knife Sharpener Waterstone with NonSlip Rubber Base & Flattening Stone. This is my first wetstone. First off I tried to sharpen my Chicago Cutlery boning knife. This knife is nearly thirty years old, has been abused in may ways and was quite dull. It was very difficult for me to get a burr on this blade, which I attribute to poor technique. Next I moved on to my Henckels Professional S paring and chef's knives. The paring knife was moderately sharp and was modestly improved after working over all three grits of stone. It would cut paper but again it was difficult to develop a burr with this blade. Undaunted I switched to the chef's knife. This knife is twenty years old and has never been professionally re-sharpened. I have sharpened it twice with a Lanksey sharpening system which marred the finish but did put a good edge on the blade. Lansky Standard Coarse Sharpening System with Fine Hones. The chef's knife was moderately dull and had several pits visible on the cutting surface. I modified my technique for passing the knife over the stone and worked the chef's knife over the 400 grit stone aggressively and eventually I was able to get a burr to form from the tip of the knife all the way to the handle. From there it was a simple process of reforming the burr on the 1000 grit stone and then finishing on the 6000. After sharpening, the chef's knife easily and cleanly slices a tomato with very light pressure and is in my opinion very sharp. Not sushi knife sharp but more than enough for the chopping and slicing I expect of it. I'm looking forward to going back and working both the boning knife and the paring knife over again. Don't expect a good result from this product the first time you use it. Watch videos on using a wetstone, expect to spend at least twenty minutes per knife at first, and practice forming a burr. If you can form a burr, you will be able to successfully sharpen your knife.
×