I love sharing information, please never hesitate to comment if you are stuck or need some advice on water stones. Speaking of that, if you have more than one stone, start with the coarse and end with the fine stones and repeat the process on each stone. However, you only need P4 pressure on that first stone, the the Raising of the Burr Pressure. After that, keep it moderate to light.
We tend to recommend natural Japanese water stones only to experienced users who are thoroughly familiar with the synthetic Japanese sharpening stones. Natural stones are not to everybody’s taste and there are inevitably many uncertainties with regard to their grit grade, which cannot be determined exactly, their hardness and their suitability for certain types of steel.
Visually, a very sharp knife has an edge that is too small to see with the eye; it may even be hard or impossible to focus in a microscope. The shape near the edge can be highlighted by rotating the knife and watching changes in reflection. Nicks and rolled edges can also be seen, as the rolled edge provides a reflective surface, while a properly straightened edge will be invisible when viewed head-on.

Beginning on the right side of the knife, move from tip to heel and heel to tip, then flip the knife and repeat. For the left side, it’s opposite—start at the top of the stone to reach the heel area completely. So, you will move from heel to tip and then tip to heel. Remember to apply and release pressure as you did earlier, exactly the same as in Step 2, but with light, refining pressure.
Some recommended products may use affiliate links. ProHuntingKnife.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Amazon and the Amazon logo are trademarks of Amazon.com, Inc or its affiliates.
The video above, from the How To You YouTube channel, explains everything you need to sharpen with a whetstone at home, and the best methods for doing so. Obviously, you’ll need a whetstone (as well as a few other things), and you’ll want to work near your sink or a bucket so you have easy access to water. Fill a container with water, then soak the whetstone in it until it stops bubbling. Inspect your blades for any trouble spots, and get to sharpening using the methods and motions described in the video; making sure to check your progress as you go. We’ve talked about sharpening knives with whetstones before, but this guide is a bit more thorough and the old video has since been removed.
Your kitchen knife becomes dull when the metal at the primary edge, the cutting edge becomes fatigued and rolls over to one side or both sides of the blade. This is normal, it should happen regardless of the quality of the steel and what you are using the knife for. The difference will be “when” it gets fatigued, the better the steel the longer the edge will hold out, generally speaking. However, I have noticed something with high quality knives such as a Fujiwara and this may be applicable to you: I have several different brands of knives ranging from mediocre to my one dream knife. Theoretically, the mediocre knives with their mediocre steel should become dull faster under normal use. (I am referring to use at home, not in professional kitchen and not in the hands of someone who cuts lotus blossoms all day long)

at the end, metal is going to vanish. Don’t start with a Dollar Store knife, start with a medium quality 8 inch (203mm) that has not been sharpened beyond the factory before you. You want to set the sharpening stage for success, a cheap knife is hard to sharpen because of the inferior quality of the steel. Now if you are worried about scratching the blade of the knife, you shouldn’t be but if that apprehension is going to distract you, eliminate the fear by taping the blade of the knife with painters tape, just the blade, not the edge.
Basically, there are 3 types of whetstones, Arato (rough grits), Nakato (medium grits) and Shiageto (fine grits). We normally use Nakato for the sharpening, but you can start with Arato to correct rough or damaged edge, and then Nakato and finish with Shiageto to get a fine and keen edge. All the sharpening methods and processes are same. However, it is not recommended to sharpen the opposite flat side of the blade with Arato
HIGH-QUALITY DOUBLE-SIDED KNIFE SHARPENING STONE: Coarse side 1000 grit leaves metal edge with frosted appearance. Edge sharpness equivalent to majority of factory edges on knives, tools; Fine side 4000 grit is ideal for finishing and polishing the edge, make edge very sharp, and edge reflects light well. Perfect for light touch-ups to an already sharp.
In addition, the most prized of the natural Japanese Water Stones are quarried in the Narutaki District north of Kyoto, Japan and are commonly available as either bench stones or pocket stones in grits ranging from 120 to 12,000. On the other hand, synthetic water stones are made from Aluminum Oxide and commonly available as either bench stones or pocket stones as well in grits ranging from 220 to 8,000 and, although this is the same abrasive material used to make India Oil Stones, the difference between the two is that the binder that holds the abrasive together enables Water Stones to be much softer than India Oil Stones which, in turn, promotes faster cutting because the worn abrasive material breaks away more quickly and is replaced with fresh, sharp, abrasive material more quickly. In addition, because water stones do not become glazed or loaded with swarf like oil stones can, new abrasive particles are constantly exposed as the stone wears so it continues to cut consistently. Plus, they can be lubricated effectively with water (rather than oil which can ruin some water stones) which combines with the fine particles of abrasive from the surface of the stone to form a slurry which polishes the bevel as the stone cuts. However, it should also be noted that Water Stones do become uneven significantly faster than other types of whetstones although, their softness does make them easier to true again.