You must put the knife blade's position at the perfect angle which is called "against the stone." What's important is the blade should be facing opposite from you. Where you've determined where the bevel angle is located, then this is what you will position against the stone. It's a good idea to know the differences between various angles for certain blade uses. There's a certain height of the blade that it should be from the stone. You'll be able to find various charts on height of the blade online. Normally, for a pocket knife or kitchen knife, it'll be 17° - 22° angle against the stone. The "Rule of thumb" is the smaller the angle, the sharper the knife. Most makers will have it in the instruction or on their official website.
A shinkansen is a Japanese-style pull-through sharpener named after the famous bullet train. It features two sets of ceramic wheels set at the right angle for sharpening a Japanese blade, which takes out the guesswork of the waterstone. Simply hold the handle with your left hand, then saw back and forth gently through the coarser wheel to sharpen, before switching to the finer wheel to polish.
Though "whetstone" is often mistaken as a reference to the water sometimes used to lubricate such stones, the term is based on the word "whet", which means to sharpen a blade,[1][2] not on the word "wet". The verb nowadays usually used to describe the process of using a sharpening stone is to sharpen, but the older term to whet is still sometimes used. The term to stone is so rare in this sense that it is no longer mentioned in for example the Oxford Living Dictionaries.[3][4] One of the most common mistaken idioms in English involves the phrase "to whet your appetite", too often mistakenly written as "to wet". But to "whet" quite appropriately means "to sharpen" one's appetite, not to douse it with water.
Cost – While you can get a perfectly serviceable sharpening stick or stone sharpener for short money and some very high-quality tabletop manual 2 and 3-stage sharpeners for less than $50, high-quality mechanical systems will often run you $200 or even more. While that’s not so much money it’s likely to impact the quality of your life it is a lot to pay to keep a decent edge on your knives. While how much you ultimately pay for a sharpener is entirely up to you, you may want to consider your commitment to cooking and how often you are actually liable to use the device. If this is your first sharpener you might also want to consider learning how to sharpen a blade using a classic stick or stone sharpener first, before deciding if moving up to a mechanical sharpener is the right thing for you.
Shapton Glass 320, 500, 1,000, 2,000 and 16,000. I have the 4,000, and 8,000, they are absolutely fine, great in fact but I just don’t use them as much as the others. These stones excel on knives made of hard steel, the hardest steel is no match for these. This does not mean you can’t sharpen hard knives on the Naniwa brand of course, you can. I have been using this particular brand of stone for many years and I absolutely love them.
My name is Peter Nowlan, a retired Naval Officer. I became interested in Knife Sharpening 35 years ago starting on oilstones after watching my father sharpen a chisel. It was a trial and error thing at that time as there was no internet back then and nobody I knew had the same interest. I started my business, New Edge Sharpening, in Halifax (Canada) to make extra money just to feed my obsession with water stones but the business took off and I am truly enjoying an abundance of dull knives to sharpen.

I've been using this stone for months and have started to find that, while the fine side does provide a nice sharp edge, the 400gr side is wearing my knives unevenly, which causes me to be unable to finely sharpen the entire length of the blade when moving to the fine side. The logo that is put in the middle of the 400gr side of the knife is causing more material to be removed than the rest of the blade when I'm sweeping across. I even verified this by going straight down the length of the fine side and watching the wear pattern come from the material coming off of the knife onto the stone.
The Sunrise Pro doesn’t have the pedigree of some other knife sharpeners on our list but it performs as advertised and that’s all that matters. For a relative song you get to restore all the knives, steak knives, cleavers in your kitchen to near pristine condition. It’s easy to use and the nice strong suction cup on the bottom means you can put the band aids away.
Now you may wonder, if a finer stone produces a better cutting edge why do I need a coarse stone at all? The answer is that finer stones work much more slowly than coarse ones. The amount of metal a fine stone removes with each pass is much less than what a coarse stone removes. If you have an edge with a good shape to it from a coarse stone, this is not a problem because the fine stone doesn’t have to remove much metal to improve the edge. If the edge is dull, it will take many times longer to reshape it with a fine stone than it would with a coarse one.