For the common sharpening purpose, generally, people tend to use two phases. In the first phases, they use the coarse stone to shape the edges then jump to the finer stone. In application, these of the two phases can be extended with the grit stone in between. It might be varying in the number of grits or mesh in different types of sharpening stone.
An extremely well written and informative article on sharpening. Overtime we all get to love certain stones for our sharpening needs. I am a huge coticule fan, and although i have used all the others, i always come back to this natural stone above all others. Still trying to figure if i chose it or it chose me! NEver the less there are so many options out there it is not hard with a little time and effort to find the right combination for your needs.
There will be a drawer that extends into the mechanism under the abrasives. Any detritus from the sharpening process drops into this drawer. Exactly where the drawer is located will differ from sharpener to sharpener but it shouldn’t be hard to find. Remove the drawer flick any material into the wastebasket and then wipe out the drawer with a damp cloth or tissue. You may want to use work gloves and goggles to protect your hands and eyes from any loose metal shavings. Once the drawer is clean and dry replace it. The exact means by which the sharpening mechanism itself is cleaned will vary from manufacturer to manufacturer. Consult your owners guide for specific details. Make sure you don’t introduce any grease or other lubricants into the sharpener unless specifically directed to do so by the owner’s manual. Also, the outside of the sharpener should come perfectly clean with just a damp cloth. Avoid using commercial cleaners or abrasives of any kind.
The paper test - Remove your knife from the sharpener. Grab a piece of notebook paper and hold it vertically in your hand so that one edge is facing straight up. Now take the knife and push it down against this edge. If the blade cuts through without hesitation it’s sharp. If the paper simply crumples beneath the blade instead of cutting the blade needs a bit more work.
In most cases a sharpening stone will be a combination of sharpening grains and a binding agent. However, in case of a Ardennes Coticule it is a completely natural product. The grains have cutting edges which enables them to sharpen your knife. As soon as a sharpening stone is used little pieces of the grains break off, revealing a new cut ing edge. The higher the number, the finer the grain. Stones with coarse grains (up to grain 400) can be used to shape the blade of a blunt knife. You can subsequently take care of the fine finish with a stone with a smaller grain.
For instance, American Novaculite (aka Washita and Arkansas Stones) is a form of metamorphic Chert that produces some of the best known and best loved natural whetstones in existence. Then, there is a form of Belgian Coticule which has been known for providing extra-keen edges since Roman times and, there is a Japanese Siliciclastic sedimentary stone (aka Japanese Water Stones) which consist of a fine silicate particles suspended in a clay matrix. Plus, there are also various types of man-made whetstones available such as Silicon Carbide (aka Crystalon) stones and Aluminum Oxide (aka India Stones) as well as a synthetic Corundum (aka Ruby) rod and Aluminum Oxide impregnated ceramic rods as well as several different types of diamond hones.
I can personally verify that this will get your knives very sharp. I will spare you all the gory details, but the picture is of the instructions the ER sent me home with after stopping the bleeding and patching me up. I have to say, that’s not what I had in mind regarding “Thanksgiving tips”. So: not only will knives slide easily through spinach, but they will go through finger and fingernail like a hot knife through butter after being sharpened by this whetstone. Very clean, straight cut. Impressive, really. Just take it slow and don’t be a moron like me.
This wedge ends up short of a "point" to a much larger degree than the picture would indicate. The metal stops short, but then there is black non-slide "tape" applied to one side, and white "slide" tape applied to the other side, which makes the wedge even thicker than it appears in the photo, which means that in practice the end of wedge is even more truncated. So I have a hard time supporting my knives accurately on this wedge while sliding them down into contact with my stones. Prior to buying this wedge I just used a wooden wedge I cut off of a 3" by 3" post using a miter saw, said wedgewhich has a much less truncated end. That wooden wedge unfortunately absorbs water from my Japanese Waterstones. But I will try spraying polyurethane on that wooden wedge to help waterproof itand try again. If that doesn't work I will try to find a 3" by 3" plastic trim board somewhere and cut a wedge off the end of that. Note that you can buy 20 degree plastic wedges, but this is the first one I have found that does 15 degrees (nominal.) Note that Amazon also has the Blue AngleGuide set of wedges, but they are very small https://www.amazon.com/Angle-Guides-Sharpening-Knife-Stone/dp/B01N4QMO7U/ref=sr_1_4?ie=UTF8&qid=1499301705&sr=8-4&keywords=sharpening+angle+guide
However, because the Belgian Blue stone generally occurs in relatively wide columns with much thinner layers of Vielsalm Coticule on either side adjacent to the slate, the Belgian Blue stone is more plentiful that Coticule and thus, it’s somewhat less expensive. But, it’s also somewhat softer than Coticule and is not divided into different grades as Coticule is. Furthermore, because it is a softer stone than Coticule, it is sold without a substrate layer.