You will be given access to our useful online learning material: a set of videos and articles to help you improve your sharpening technique. These resources were made by professional knife sharpeners, specifically for beginners and intermediate sharpeners. The articles and videos will guide you and teach you knife sharpening from scratch, also covering more advanced techniques. You can also get in touch with us anytime if you have any questions concerning sharpening specific types knives.
Unfortunately, the arrays of modern whetstone can be bewildering to the inexperienced sharpeners that so often times many of them end up with a crap or wrong decision on stone type for their utensils. The most difficult to determine is whether the whetstone is fake or fabricated with low quality of materials. To avoid this you can only go for the reliable brand of a whetstone.
Although there are many ways to sharpen your kitchen knives, we believe that using a sharpening stone is the absolute best way to go about it. Not only will you get the best results, you won’t assume as much risk of damaging the blade as you would using a manual or electric knife sharpener. The problem for most home cooks, however, is finding the best sharpening stone and learning how to use it. I’m not going to pretend it’s as easy as purchasing a stone and digging right in.
Made from hand-selected A36 hot rolled steel that is left untreated to allow it to age naturally and beautifully from season to season, Stahl's new X firepit will be a center of warmth and attention for generations. Each minimalist firepit is made in Portland, Oregon and includes four 3/16 inch steel pieces that can be assembled in minutes with no complicated parts or screws.
If in doubt or just learning, a safe bet is a set of quality synthetic stones. They’re the easiest to use, require the least maintenance and are the most forgiving. If you’re just starting out we highly recommend the Naniwa Sharpening Stones. They’re excellent quality, reliable, durable and no soaking time is required. For advanced users we recommend the Naniwa Pro sharpening stones or Kaiden Ceramics.
A great sharpener for all your kitchen knives the CS2 also makes a smart addition to the gear when you’re going away on a family camping trip. It will also do a bang-up job on your hunting, pocket, boning knife and more. As mentioned it does require just a bit of getting used to in order to achieve optimal results but nothing too involved. A simple, effective, no-frills sharpener.
JosephineDC.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, JosephineDC.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Sharpening is really two processes: Grinding and honing. Grinding is simply the removal of metal. Honing is a precision abrasion process in which a relatively small amount of material is removed from the surface by the means of abrasive stones. Once you have the right shape, usually using a more aggressive grit, you then switch to a finer grit to hone the edge.
I'm a novice knife sharpener. I've had to unlearn what my grandpa taught me in order to use these. So far, I've had decent but mixed results. I've switched to my cheap 200/400-ish cheap tool stone from harbor freight for cutting a bevel when the blade has either been damaged or did not have a proper bevel. The 400/1000 grit stone in this kit is soft. Very soft. I have bowled it out several times. It makes keeping a steady angle difficult. But these stones at this price point are meant for learning, and for that they serve their purpose.
Whetstones may be natural or artificial stones. Artificial stones usually come in the form of a bonded abrasive composed of a ceramic such as silicon carbide (carborundum) or of aluminium oxide (corundum). Bonded abrasives provide a faster cutting action than natural stones. They are commonly available as a double-sided block with a coarse grit on one side and a fine grit on the other enabling one stone to satisfy the basic requirements of sharpening. Some shapes are designed for specific purposes such as sharpening scythes, drills or serrations.
I am just starting out sharpening with whet stones. I have found these stones to be very nice and the instructional videos that come along with the set on knifeplanet are extremely helpful to anyone starting out. The cost of the set was very reasonable and seems to be a great value. The customer service is amazing, I lost the site for the videos and sent an email to get the information and immediately there was a reply with all of the links that I needed. I appreciate their attention to their customers!!
The most important aspect of a sharpening stone is the grit. If you have knives that have taken a beating and are either nicked up or really dull, you’ll need a courser stone to get it back into shape. And in order to put an exceptionally sharp edge on an already sharp knife, you’ll need a finer grit stone. If your knives are already in pretty good shape and just need a touch up, buying just a finer grit stone might be enough, but don’t think you can get away without a courser stone for knives that need more TLC. It is possible to buy a combination, or two-sided sharpening stone.
Just to prove that we're not merely sharpening geeks, here's an interesting side note. The word whet pops up in some unexpected places. A small species of owl is called the saw-whet owl because the sound it makes reminded people of the sound made when sharpening a saw with a file. And the phrase "to whet your appetite" comes from the idea of your hunger growing sharper at the thought of food.
We’re happy to present something everyone has been waiting for – a combination diamond/ceramic whetstone that will handle all your sharpening needs. The newly-developed DC3 and DC4 whetstones consist of a fine diamond stone (25 micron) and a very special ceramic stone, made of synthetic sapphires. The advantage of these materials, although they get worn, will still keep their flat shape this is important when you sharpen your knife. And, since these materials are the hardest we know of, they will sharpen any steel, even these extremely hard powder steels. You don’t need any lubrication for these stone but now and then you should consider cleaning them with warm water and liquid soap. The stones might feel coarse from the start but will become smoother/better after some use. A leather pouch is included.
I purchased this set together with the 400/1000 grit stone assuming that some of my knives were quite dull and would need work on a coarse grit stone. Premium Whetstone Sharpening Stone 2 Side Grit 400/1000 | Knife Sharpener Waterstone with NonSlip Rubber Base & Flattening Stone. This is my first wetstone. First off I tried to sharpen my Chicago Cutlery boning knife. This knife is nearly thirty years old, has been abused in may ways and was quite dull. It was very difficult for me to get a burr on this blade, which I attribute to poor technique. Next I moved on to my Henckels Professional S paring and chef's knives. The paring knife was moderately sharp and was modestly improved after working over all three grits of stone. It would cut paper but again it was difficult to develop a burr with this blade. Undaunted I switched to the chef's knife. This knife is twenty years old and has never been professionally re-sharpened. I have sharpened it twice with a Lanksey sharpening system which marred the finish but did put a good edge on the blade. Lansky Standard Coarse Sharpening System with Fine Hones. The chef's knife was moderately dull and had several pits visible on the cutting surface. I modified my technique for passing the knife over the stone and worked the chef's knife over the 400 grit stone aggressively and eventually I was able to get a burr to form from the tip of the knife all the way to the handle. From there it was a simple process of reforming the burr on the 1000 grit stone and then finishing on the 6000. After sharpening, the chef's knife easily and cleanly slices a tomato with very light pressure and is in my opinion very sharp. Not sushi knife sharp but more than enough for the chopping and slicing I expect of it. I'm looking forward to going back and working both the boning knife and the paring knife over again. Don't expect a good result from this product the first time you use it. Watch videos on using a wetstone, expect to spend at least twenty minutes per knife at first, and practice forming a burr. If you can form a burr, you will be able to successfully sharpen your knife.
When you apply a sharp knife to the surface of a tomato, cucumber, carrot or other food item it should - if you are holding it firmly and applying minimal pressure - sink into the particular item without effort. As such all you really need to work on is your technique and making sure you keep your fingers out of the way. With a dull knife however things aren’t quite so simple. When you apply a dull blade to, say, a tomato it’s not going to slice into the skin. Instead the skin will be able to push back meaning you’ll need to apply ever more pressure to get the knife to penetrate. Increasing the pressure on the knife increases the likelihood of the knife slipping off the offending food item to one side or another. And if it slips to the side where your hand is attempting to hold the vegetable steady you could be in store for a very nasty cut. Because even a dull knife will cause injury if there’s enough force behind it.
Your task as a sharpener is to remove that fatigued metal and expose the steel underneath, the fresh strong steel and bring side A and B of the knife together at the Apex precisely, sounds easy doesn’t it? Like peeling a layer off and having a fresh start, over and over. Of course there is much more to it than this but in very basic terms, you want the abrasive properties of the water stone to abrade the fatigued metal away, like an eraser.
Push the point you want to sharpen with your fingers. While keeping the angle and pushing the point with your fingers, stroke the blade until it reaches the other edge of the whetstone, then pull the blade back until it reaches the edge of the whetstone. This back and forth is counted as one stroke. Repeat it for about five strokes until you can see or feel some small burrs (edge curvatures) Then move the position of your fingers to where you have not sharpened yet, and repeat this five strokes of sharpening processed from the tip to the base of the blade.
Diamond sharpening stones are becoming really popular because of their ability to cut fast. We tend not to recommend diamond sharpening stones/plates because a lot of damage can be done very quickly. Also diamonds are pretty sharp and at arato level they leave deep scratches in the blade that need to be polished out quite aggressively. Diamond stones can be used with and without lubricant.
The Chef’s Choice 316 sharpener will restore your dull knives to professional sharpness. It’s a great, reliable, well-built kitchen appliance that requires no special knowledge or setup. The precision guides of the 2-stage system make sure the blade is firmly held at the correct angle so that optimal sharpening is realized with minimal fuss. Great for your Asian-style knives or those you’d like to endow with an Asian-type edge for some precision cutting.
J. Kenji López-Alt is the Chief Culinary Advisor of Serious Eats, and author of the James Beard Award-nominated column The Food Lab, where he unravels the science of home cooking. A restaurant-trained chef and former Editor at Cook's Illustrated magazine, his first book, The Food Lab: Better Home Cooking Through Science is a New York Times Best-Seller, the recipient of a James Beard Award, and was named Cookbook of the Year in 2015 by the International Association of Culinary Professionals.
Choose the style of stone. You'll need to choose a natural or synthetic stone that can be used wet (soaked in water), with oil, or dry. There are also diamond stones that are actually very small diamonds attached to a metal surface. Stones that are soaked in water are softer stones which means you can quickly sharpen your knives. Unfortunately, these stones will wear down faster than the others. Oil stones are the least expensive and they're made of a harder material.
Ease of use – Most people in search of a mechanical sharpener want one because they don’t want to be bothered with trying to achieve a perfect edge themselves using a stick or sharpening stone. They want predictable, first class results every time. In that case it’s important that the electric powered device is easy to use, achieves results quickly and with little effort and is designed with user safety in mind. Keep in mind too that it’s easy to apply too much pressure when using a mechanical sharpener and when that happens you’re likely to see unsatisfactory results. In addition there are subtle differences between mechanical devices designed for Asian-style knives and those designed for Western-style knives. This has to do with the sharpening angle discussed above. Don’t get an Asian sharpener if you don’t need precise control over your cuts.
The stones from Shapton are probably the hardest of all Japanese sharpening stones. They will remain flat for a long time. They are therefore the best choice if you are looking for a relatively coarse stone that cuts quickly without having to be dressed repeatedly. The finer-grained stones also work very well. But Shapton stones do not provide the mirror finish you can achieve with softer stones.
The purpose of this article is just to get you started on the right path and please note that this is just the way I do it, there are many gifted sharpeners out there who are eager to share their knowledge. (I am not calling myself a gifted sharpener by the way, I just have so much respect for many sharpeners so I’m calling them gifted, they call me Peter).
at the end, metal is going to vanish. Don’t start with a Dollar Store knife, start with a medium quality 8 inch (203mm) that has not been sharpened beyond the factory before you. You want to set the sharpening stage for success, a cheap knife is hard to sharpen because of the inferior quality of the steel. Now if you are worried about scratching the blade of the knife, you shouldn’t be but if that apprehension is going to distract you, eliminate the fear by taping the blade of the knife with painters tape, just the blade, not the edge.
Practice holding the knife at a 20 degree angle. Most straight blades need to be sharpened at a 20 degree angle. To find the angle, hold the directly in front of you so it's straight up and down. This is 90 degrees. Tilt the knife halfway towards the table so it's at a 45 degree angle. Tilt the knife halfway again so it's about an inch (2.5 cm) above the table. This should be a 20 degree angle.
However, it should also be noted that “water stones” are generally significantly softer than oil stones and thus, water stones generally cut faster than oil stones but, they also have to be flattened more often that oil stones do. Furthermore, it should be noted that some water stones must be soaked in water for several hours prior to use whereas, others are of the “splash and sharpen” variety and thus, they only need to be soaked for a few minutes before use and then wetted down occasionally during sharpening process. Diamond hones on the other hand are more durable than either water stones or oil stones and, because they generally have a more coarse grit, they cut faster than natural whetstones. Plus, due to their construction, they never need truing and, in fact, coarse diamond hones are often used to flatten both natural and synthetic whetstones.
Let’s talk about the tip of the knife, the burr needs to be formed here as well. Here is a simple trick that works, I like keeping things simple. As you get to the tip area of the knife, the front inch, raise your elbow so that it is parallel to the ground, you can also raise your sharpening angle very slightly but just raising your elbow will perform wonders and likely eliminate the tip sharpening area issue, it is an issue for some.
The toughest angle to master is the angle at which you'll sharpen the edge of the knife. For a Japanese knife, that should be around 12-15 degrees. Before you reach for the protractor, a good test is to get roughly half an index finger's gap between the spine of the knife and the stone (see above). Remember to remove your finger before you start sharpening. For a Western-style knife, you want an angle of about 20°, so raise it ever-so-slightly higher.
Though "whetstone" is often mistaken as a reference to the water sometimes used to lubricate such stones, the term is based on the word "whet", which means to sharpen a blade, not on the word "wet". The verb nowadays usually used to describe the process of using a sharpening stone is to sharpen, but the older term to whet is still sometimes used. The term to stone is so rare in this sense that it is no longer mentioned in for example the Oxford Living Dictionaries. One of the most common mistaken idioms in English involves the phrase "to whet your appetite", too often mistakenly written as "to wet". But to "whet" quite appropriately means "to sharpen" one's appetite, not to douse it with water.
The video above, from the How To You YouTube channel, explains everything you need to sharpen with a whetstone at home, and the best methods for doing so. Obviously, you’ll need a whetstone (as well as a few other things), and you’ll want to work near your sink or a bucket so you have easy access to water. Fill a container with water, then soak the whetstone in it until it stops bubbling. Inspect your blades for any trouble spots, and get to sharpening using the methods and motions described in the video; making sure to check your progress as you go. We’ve talked about sharpening knives with whetstones before, but this guide is a bit more thorough and the old video has since been removed.