A great sharpener for all your kitchen knives the CS2 also makes a smart addition to the gear when you’re going away on a family camping trip. It will also do a bang-up job on your hunting, pocket, boning knife and more. As mentioned it does require just a bit of getting used to in order to achieve optimal results but nothing too involved. A simple, effective, no-frills sharpener.
A: Another issue that comes up with electric knife sharpeners is how to clean them. Or if, in fact, they actually need cleaning at all. The answer to the second question is that yes, they do need to be cleaned occasionally. And by occasionally we mean once a year or so if you use them with any frequency. Obviously if you’ve only used the sharpener a few times then there’s no compelling reason to clean it, other than just wanting to keep things tidy (and there’s nothing wrong with that). So, having established that sharpeners do need to be cleaned occasionally you need to know how to do so in a safe and effective manner. It’s not complicated.
I've been using these stones for the past day, and they work great. Once you get the technique down that works for you, you can sharpen any knife to the point it can cut through news paper. Tip: make sure you count the amount of times you pass through the stone on one side and do that same amount on the other side. What I usually do is if I know the knife is very dull or chipped, I do 100 passes on each side using the 400 grit. I test the blade on thick paper and if it cuts through I test it on news paper. If it doesn't cut through the news paper I do another 50 passes on each side. Repeat this until the blade can cut through newspaper. After, on the 1000,3000, and then the 8000 grit stone I do 50 passes on each side. This should make the blade very smoothe cutting and polish it. I plan on getting a strop or piece of leather to further polish the blade. The only thing I don't like about this is that this package is that it does not come with a dressing stone so you can re flatten/level the stone after using them.
If you do not remove enough metal to create a new edge, you will leave some of the dull edge in place. A dull blade (or a blade with dull spots or nicks) will reflect light from the very edge of the blade. A razor sharp knife edge will not show "bright spots" when you hold it blade up under a bright light. You will need to remove enough material from the sides of the bevel so that the edge stops reflecting light.
We get asked regularly to recommend stones for the beginning sharpener. Everyone wants to get stones that will be of the most practical use. No one wants to waste money on something they will have to replace later. The goal is to get stones that can be used as a foundation for your future needs. But the number of options available can be bewildering to the inexperienced sharpener, leaving many wondering where to start.
If no metal is being removed from the edge of the blade, it’s considered honing. Whereas if metal is being removed from the blade edge this is considered sharpening. Certainly, even honing will result in some microscopic amounts of metal being removed from the blade edge but not enough to be visible to the human eye, so the above definition is basically a solid one.
Diamond hones are made from very small, industrial grade, diamonds adhered to the face of a metal or plastic plate. Also, because Diamonds are so much harder than any of the other sharpening materials, they tend to cut very fast and last much longer than the other whetstone materials. But, they are also often more expensive to purchase. In addition, Diamond Stones generally consist of three different styles consisting of a solid metal plate coated with an adhesive and diamond dust with holes in the plate to allow the swarf to escape, a solid plate without holes for sharpening tools with corners that might catch in the holes, and a plastic plate with islands of exposed plastic interspersed with the adhesive and diamond dust to act as a lubricant.
Now you may wonder, if a finer stone produces a better cutting edge why do I need a coarse stone at all? The answer is that finer stones work much more slowly than coarse ones. The amount of metal a fine stone removes with each pass is much less than what a coarse stone removes. If you have an edge with a good shape to it from a coarse stone, this is not a problem because the fine stone doesn’t have to remove much metal to improve the edge. If the edge is dull, it will take many times longer to reshape it with a fine stone than it would with a coarse one.