To take off the fine scratches and burrs left by coarser stones, and to polish the surface, you can use stones starting at around 2000 grit. There is theoretically no upper limit, but stones above about 10000 grit achieve practically no measurable improvement in the edge. It is also interesting to note that above 8000 grit, there is no Japanese measurement standard. For stones labelled as having a finer grit, you simply have to take the manufacturer's word for it.
A: When it comes to the best knife sharpeners used in a domestic setting the abrasives used to sharpen the blade should last for quite a few years. When they do eventually wear out many of the best manufacturers will refurbish them for you, typically for a nominal fee. Again, however, unless you are using the sharpener on a daily basis (and there is virtually no reason the average person would do this), the sharpener should last for many years before ever needing service.
We get asked regularly to recommend stones for the beginning sharpener. Everyone wants to get stones that will be of the most practical use. No one wants to waste money on something they will have to replace later. The goal is to get stones that can be used as a foundation for your future needs. But the number of options available can be bewildering to the inexperienced sharpener, leaving many wondering where to start.
I know that it is very helpful to watch a video of this process and the best videos of knife sharpening I have seen are out there for you. If you only watch one person sharpen a knife, watch Jon Broida from Japanese Knife Imports. Extremely professional videos and easy to understand. I have a couple of videos as well on my website but I really like what Jon has done for the sharpening community.
For this type of hand held manual sharpener the 463 does an extraordinary job thanks mostly to the diamond abrasive wheels. You get an edge that’s both razor sharp and burr-free, as if you spent an hour working the edge on an oil stone. If people make a mistake with the 463 it’s that they assume more pressure is needed than actually is. Keep in mind though that it really shines on serrated and straight edged, double bevel Asian-style knives.
However, it should also be noted that “water stones” are generally significantly softer than oil stones and thus, water stones generally cut faster than oil stones but, they also have to be flattened more often that oil stones do. Furthermore, it should be noted that some water stones must be soaked in water for several hours prior to use whereas, others are of the “splash and sharpen” variety and thus, they only need to be soaked for a few minutes before use and then wetted down occasionally during sharpening process. Diamond hones on the other hand are more durable than either water stones or oil stones and, because they generally have a more coarse grit, they cut faster than natural whetstones. Plus, due to their construction, they never need truing and, in fact, coarse diamond hones are often used to flatten both natural and synthetic whetstones.
The Chef’s Choice 316 sharpener will restore your dull knives to professional sharpness. It’s a great, reliable, well-built kitchen appliance that requires no special knowledge or setup. The precision guides of the 2-stage system make sure the blade is firmly held at the correct angle so that optimal sharpening is realized with minimal fuss. Great for your Asian-style knives or those you’d like to endow with an Asian-type edge for some precision cutting.
Feedback is something that is very important to most sharpeners, i.e. how the stone feels when you are using it. Does it feel smooth, creamy and silky or does it feel hard and scratchy. While feedback, pleasant or unpleasant may be a purchase deterring factor it really doesn’t have any effect on level of sharpness that the stone can deliver. Unless of course the feedback is so distracting that it hinders the sharpeners focus and enjoyment and as a result, the sharpener doesn’t like what he/she is doing so that ultimately it does have the potential to negatively impact the results.
Cost – While you can get a perfectly serviceable sharpening stick or stone sharpener for short money and some very high-quality tabletop manual 2 and 3-stage sharpeners for less than $50, high-quality mechanical systems will often run you $200 or even more. While that’s not so much money it’s likely to impact the quality of your life it is a lot to pay to keep a decent edge on your knives. While how much you ultimately pay for a sharpener is entirely up to you, you may want to consider your commitment to cooking and how often you are actually liable to use the device. If this is your first sharpener you might also want to consider learning how to sharpen a blade using a classic stick or stone sharpener first, before deciding if moving up to a mechanical sharpener is the right thing for you.
Begin with your lower-grit stone. Place the heel of your knife on the far edge of the stone, holding the blade gently but firmly with both hands at a 15- to 20-degree angle. Using even pressure, slowly drag the knife over the stone toward you down the length of the stone while simultaneously moving the knife such that the contact point moves toward the tip of the blade.
A: That depends almost entirely on how often you use them. If you are a professional chef who uses his or her knives every day then you should hone them every time you use your knives. But honing has its limits and over time your edge is going to become dull no matter what. Therefore your knives will need to be sharpened at least several times a year. Some chefs, in fact, will use a whetstone on an almost daily basis in order to ensure their knives are always razor sharp. Most of us, however, are not professional chefs and may not even touch our kitchen knives for days at a time. In that case, it’s probably a good idea to hone the edge after every couple of uses and have your knives sharpened once a year.