TO USE: Soak stone in water for no more than 5-10 minutes. Place stone on a damp cloth with the courser 400 grit side (dark green) facing up. Hold the knife so that it’s flat and perpendicular to the block, with the blade facing left. Holding the knife at a 20-degree angle, slowly sweep the edge of the blade from left to right down the length of the stone and continue until sharp. If stone starts to feel too dry, add more water. Be patient and take your time. Flip knife over and repeat on the other side (now moving from right to left). Be sure to sharpen both sides evenly. To polish the blade further, flip stone over to the fine 1000 grit side (light green) and repeat the process. When blade is honed to desired sharpness, wash and dry your knife. To clean your stone, simply rinse with water, wipe away any remaining metal residue with a rag, rinse again, then dry.
Ease of use – Most people in search of a mechanical sharpener want one because they don’t want to be bothered with trying to achieve a perfect edge themselves using a stick or sharpening stone. They want predictable, first class results every time. In that case it’s important that the electric powered device is easy to use, achieves results quickly and with little effort and is designed with user safety in mind. Keep in mind too that it’s easy to apply too much pressure when using a mechanical sharpener and when that happens you’re likely to see unsatisfactory results. In addition there are subtle differences between mechanical devices designed for Asian-style knives and those designed for Western-style knives. This has to do with the sharpening angle discussed above. Don’t get an Asian sharpener if you don’t need precise control over your cuts.
Also natural stones have a random grit size that gives a long lasting edge. Basically the random grits create varying sizes of micro-serration in the blade that wear down at a different rate, therefore longer edge retention. Whether this is true or not we really like natural stone, especially for sharpening tradition single bevel Japanese knives. Use natural stones with water – it’s far cheaper than sake.
The stick – With a stick sharpener hold the sharpener in front of you (facing away from you) with one hand and the handle in the other hand. Hold the base of the knife against the base of the tip at a slight angle and then push the blade along the stick pulling it across the stick at the same time. The tip of the blade should cross the end of the stick. To sharpen the other side of the blade place it under the stick and repeat the process making sure to reverse the angle at which you are holding the knife against the stick.
To use Al's method, take a black felt pen and shade in the bevel of the knife. Then take two strokes on the stone and examine the edge. If you have maintained the proper angle then all the black will be gone. If you see black on the top of the edge it means you are holding the back of the knife too far from the stone. If there is black on the bottom of the edge but the top is clean then you are laying the knife too flat on the stone and you need to raise it a bit. Repaint the edge and try it again. Once you discover what the right angle looks like then just maintain that.
The humble sharpener tends to elicit more divergent opinions than just about any other type of kitchen tech. Everyone, it turns out, has their own take on which type of sharpener works best and why and most serious chefs aren’t shy about voicing their opinion. As you can imagine then there are a number of things most chefs – both professional and amateur – look for in a sharpener in order to ensure they get the one that’s right for them. These considerations include:
I bet those Vikings, relatives of mine no doubt, never had it so good. They never had surated blades to sharpen or needed to wear cool things around their necks to woo the women (they just grabbed them by the hair I guess). I love my stone. So useful and beautiful. I always have spit to wet it with, and I always have a way to sharpen my tool. Wazoo makes high quality products. I give them the highest rating I have. Dudes!
Feedback is something that is very important to most sharpeners, i.e. how the stone feels when you are using it. Does it feel smooth, creamy and silky or does it feel hard and scratchy. While feedback, pleasant or unpleasant may be a purchase deterring factor it really doesn’t have any effect on level of sharpness that the stone can deliver. Unless of course the feedback is so distracting that it hinders the sharpeners focus and enjoyment and as a result, the sharpener doesn’t like what he/she is doing so that ultimately it does have the potential to negatively impact the results.
Clamp-style sharpening tools use a clamp with several holes with predefined angles. The stone is mounted on a rod and is pulled through these holes, so that the angle remains consistent. Another system is the crock stick setup, where two sticks are put into a plastic or wooden base to form a V shape. When the knife is pulled up the V, the angle is held so long as the blade is held perpendicular to the base. Several cutlery manufacturers now offer electric knife sharpeners with multiple stages with at least one grinding stage. These electric sharpeners are typically used in the kitchen but have the ability to sharpen blades such as pocket or tactical knives. The main benefit of using an electric sharpener is speed with many models that can complete the sharpening process in one to two minutes. The disadvantage is that the sharpening angle is fixed so some specialized knives, like a Japanese style Santoku, may need additional attention to sharpen to the ideal angle.
One of the combinations of stones that I was introduced to several years ago is a unique one, it is a 500, 2,000 and 16,000 grit combination. I was apprehensive when I first tried this, that was thousands of knives ago, it works, it is fantastic combination. It is unique because the traditional way of thinking is that we should be doubling the grit sizes as we sharpen, for example, a 500 grit stone should be followed by a 1,000 grit, then 2,000 grit. This line of thought is meant to be flexible, it is a general rule only, I have broken it countless times.
As you probably have guessed, knives are easier to sharpen on longer stones. The width of the stone is less important than the length when sharpening knives. The longer stone allows for longer sharpening strokes and contributes to faster sharpening. The longer strokes mean fewer strokes across your stone, making it easier to maintain a consistent sharpening angle. As a rule of thumb, a small knife can easily be sharpened on a large stone, but a large knife cannot easily be sharpened on a small stone.
I purchased this set together with the 400/1000 grit stone assuming that some of my knives were quite dull and would need work on a coarse grit stone. Premium Whetstone Sharpening Stone 2 Side Grit 400/1000 | Knife Sharpener Waterstone with NonSlip Rubber Base & Flattening Stone. This is my first wetstone. First off I tried to sharpen my Chicago Cutlery boning knife. This knife is nearly thirty years old, has been abused in may ways and was quite dull. It was very difficult for me to get a burr on this blade, which I attribute to poor technique. Next I moved on to my Henckels Professional S paring and chef's knives. The paring knife was moderately sharp and was modestly improved after working over all three grits of stone. It would cut paper but again it was difficult to develop a burr with this blade. Undaunted I switched to the chef's knife. This knife is twenty years old and has never been professionally re-sharpened. I have sharpened it twice with a Lanksey sharpening system which marred the finish but did put a good edge on the blade. Lansky Standard Coarse Sharpening System with Fine Hones. The chef's knife was moderately dull and had several pits visible on the cutting surface. I modified my technique for passing the knife over the stone and worked the chef's knife over the 400 grit stone aggressively and eventually I was able to get a burr to form from the tip of the knife all the way to the handle. From there it was a simple process of reforming the burr on the 1000 grit stone and then finishing on the 6000. After sharpening, the chef's knife easily and cleanly slices a tomato with very light pressure and is in my opinion very sharp. Not sushi knife sharp but more than enough for the chopping and slicing I expect of it. I'm looking forward to going back and working both the boning knife and the paring knife over again. Don't expect a good result from this product the first time you use it. Watch videos on using a wetstone, expect to spend at least twenty minutes per knife at first, and practice forming a burr. If you can form a burr, you will be able to successfully sharpen your knife.