Learning sharpening technique requires focus even without worrying about the stone itself. Stones that require frequent flattening, soaking and cleaning, or that take a long time to create an edge can be a source of frustration to some beginning sharpeners. Keep in mind your willingness perform regular maintenance when choosing a starting set of stones.
The most important aspect of a sharpening stone is the grit. If you have knives that have taken a beating and are either nicked up or really dull, you’ll need a courser stone to get it back into shape. And in order to put an exceptionally sharp edge on an already sharp knife, you’ll need a finer grit stone. If your knives are already in pretty good shape and just need a touch up, buying just a finer grit stone might be enough, but don’t think you can get away without a courser stone for knives that need more TLC. It is possible to buy a combination, or two-sided sharpening stone.

first time buying a sharping stone. i bought this because i wanted to sharpen kitchen knives. you have to practice to get good at it, use a knife you don't care about because you might mess it up. there is some conflicting instructions online on how to use, water or no water. read as much as you can about using stones and practice, practice , practice. look up videos on youtube and internet. i had fun using it, BUY IF YOU WANT TO LEARN here is some stuff i found, they all sound like professionals http://video.about.com/culinaryarts/Sharpen-Knives-With-a-Whetston.htm?rd=1 http://culinaryarts.about.com/od/knivescutlery/ht/whetstone.htm this is a video that says don't use water http://video.about.com/culinaryarts/Sharpen-Knives-With-a-Whetston.htm?rd=1 this is a youtube video that i watched that uses water. *informative http://www.youtube.com/watch?v=KFIg9Cm-nJg

Once you've sharpened one side, you need to flip over, but don't swap the hand gripping the blade – think of it a bit like going backhand with a tennis racket (see above). Lead with the heel this time, rather then with the blade, but repeat the process in three parts. After five strokes on each third of the blade, it's time to check your knife. It's not an exact science, and it all depends on how blunt your blade was to start with (mine was very blunt indeed). But if you sharpen fairly regularly, it should just take a few strokes. 

Over the course of two days I re-sharpened nearly a dozen old blades, including removing the secondary bevel on an old stainless Ontario saber-grind Navy diver's knife, convexing the edge on flat ground 1095 Schrade 55 that also came with a secondary bevel, and fixing a broken tip on an old Kershaw folder. These stones made quick work of the Schrade and Kershaw. Both had completely new edge geometry within 30 minutes apiece. The Kershaw looked like-new, as if the tip had never broken. And the Schrade cut much better than it's secondary bevel would previously allow, regardless of how sharp I got it with a ceramic rod and strops. The Ontario took a little more work, as it had been abused a little the last time I'd held it, over 25 years ago and was as dull as a case knife - one of the reasons I decided to go ahead and do a full saber grind - well, a slightly convexed saber, I suppose would be more accurate. But within under an hour of using the two stones and a couple leather strops (one with black compound, another with green), the Ontario was shaving sharp again too.
The video above, from the How To You YouTube channel, explains everything you need to sharpen with a whetstone at home, and the best methods for doing so. Obviously, you’ll need a whetstone (as well as a few other things), and you’ll want to work near your sink or a bucket so you have easy access to water. Fill a container with water, then soak the whetstone in it until it stops bubbling. Inspect your blades for any trouble spots, and get to sharpening using the methods and motions described in the video; making sure to check your progress as you go. We’ve talked about sharpening knives with whetstones before, but this guide is a bit more thorough and the old video has since been removed.
Besides of the quality, of course, there are other things to consider when shopping a proper whetstone that would meet our needs that are relating to the type, size of the stone, and the stone grit grade. Nevertheless, it is impossible to recommend which model or type is best for every sharpener because everyone comes with different needs and requirements. The only need-to-know by beginning sharpeners are the basic things that will help them to narrow down their consideration. If it is you, read on our sharpening stone buying guide to find out some basic needs you have to pay attention before spending any penny on it.
The height of the spine of your knife off of the stone below it will determine the angle. A typical sharpening angle for a typical chef knife is 19 or 20 degrees per side. For the sake of removing confusing obstacles that could hinder your progress, let’s just sharpen your knife at 20 degrees per side. You can determine exactly how high off the stone that knife should be held by measuring the height of your blade at the heel and then dividing that number by 3 for a 20 deg angle.
Beginning on the right side of the knife, move from tip to heel and heel to tip, then flip the knife and repeat. For the left side, it’s opposite—start at the top of the stone to reach the heel area completely. So, you will move from heel to tip and then tip to heel. Remember to apply and release pressure as you did earlier, exactly the same as in Step 2, but with light, refining pressure.
The little white pieces don't seem to damage my stones, though I am careful to apply the bulk of my pressure to the blade edge. They ride back and forth just fine. There is a little bit of an art to finding the right movements so the jig doesn't fall off the side of your stone but you can still use most of the stone. It's sort of angled down and away from the top corner to the opposite bottom corner
Practice holding the knife at a 20 degree angle. Most straight blades need to be sharpened at a 20 degree angle. To find the angle, hold the directly in front of you so it's straight up and down. This is 90 degrees. Tilt the knife halfway towards the table so it's at a 45 degree angle. Tilt the knife halfway again so it's about an inch (2.5 cm) above the table. This should be a 20 degree angle.[4]
Both Belgian Blue and Vielsalm Coticule are ancient stone layers found in the Belgian Ardenne Mountains with characteristics similar to both Novaculite and Siliciclastic sedimentary stone in that it is a metamorphic stone consisting of both gray and yellow volcanic ash mixed with tiny Spessartite Garnet crystals suspended in a clay matrix. However, due to its geology, both types of stone occur only in vertical seams sandwiched between two thick layers of bluish-purple slate and thus, they must be meticulously extracted mostly by hand. However, this type of extraction process is both very time-consuming and very labor-intensive and, quarrymen can only extract the stone for a few months each year due to inclement weather conditions. Consequently, both Belgium Blue and Coticule whetstones tend to be somewhat expensive.
Now you are going to use P2 pressure, moderate and in this case the stone is going to do the work, you are just guiding the knife along, stabilizing it as the amazing water stones does it’s job. Use the exact same technique, same angle but just moderate pressure, hardly pressing down at all, you are not trying to form a burr here, that is already done, now you refining the edge and bevel, removing some of the scratches left by your first stage of the process. Here is where the knife will get sharp and it will happen quickly. Now you are removing the burr, you are cleaning up the edge, some of that fatigued metal is going to want to hang on to the mother ship, your moderate pressure is going to start taking it away, as reluctant as it is to leave, it won’t have a choice. This should only take a couple minutes just mimicking the first step but with lighter pressure and this time visualizing the burr being scraped away, it will start to vanish.
Feedback is something that is very important to most sharpeners, i.e. how the stone feels when you are using it. Does it feel smooth, creamy and silky or does it feel hard and scratchy. While feedback, pleasant or unpleasant may be a purchase deterring factor it really doesn’t have any effect on level of sharpness that the stone can deliver. Unless of course the feedback is so distracting that it hinders the sharpeners focus and enjoyment and as a result, the sharpener doesn’t like what he/she is doing so that ultimately it does have the potential to negatively impact the results.
A great sharpener for all your kitchen knives the CS2 also makes a smart addition to the gear when you’re going away on a family camping trip. It will also do a bang-up job on your hunting, pocket, boning knife and more. As mentioned it does require just a bit of getting used to in order to achieve optimal results but nothing too involved. A simple, effective, no-frills sharpener.
Siliciclastic stone is a clastic, noncarbonate, sedimentary stone that is almost exclusively silica-bearing and exists as either a form of quartz or, another silicate mineral. In addition, hardened clay is also a sedimentary stone but, it is formed from organic materials such as plant and animal matter and thus, it is much softer than Siliciclastic However, when silicon sediment is suspended in a clay matrix and then naturally hardened over thousands of years, it forms an excellent whetstone material; although, it is somewhat softer than Novaculite. Thus, because the geology of Japan once held large deposits of this type of stone it has been used for hundreds of years for sharpening tools, knives, and swords. However, unlike Novaculite, Belgian Blue, and Coticule, both natural and synthetic Japanese whetstones use water for lubrication and thus, they are commonly known as “Japanese Water Stones” because this type of stone is very porous. Thus, natural Japanese Water Stones must be soaked in water for up to twenty-four hours prior to use whereas, synthetic Japanese Water Stones can be soaked for only a few moments.
In most cases, the sharper, the better. The sharpness of your edge is determined by the angle (the lower the angle, the sharper the edge) and how fine of a grit you choose for your final honing. Since you have already determined your angle many steps earlier, now you just need to know which grit you can stop at. This again depends on the use of the knife. In most cases, go all the way to the finest stone that you own as this will give you your best edge. The only exception would be a knife used to cut soft vegetables like tomatoes, as a slightly more coarse edge will provide more of a tooth pattern for easier cutting.
To take off the fine scratches and burrs left by coarser stones, and to polish the surface, you can use stones starting at around 2000 grit. There is theoretically no upper limit, but stones above about 10000 grit achieve practically no measurable improvement in the edge. It is also interesting to note that above 8000 grit, there is no Japanese measurement standard. For stones labelled as having a finer grit, you simply have to take the manufacturer's word for it.
Once the burr is removed, it's time to test the sharpness with paper. Hold a piece of newspaper at about 45°, with a bit of tension, and slash lightly with each point of the blade. If it cuts through easily, your knife's sharp. Warner speedily lacerated his newspaper, but I of course struggled. There is an element of technique involved, he reassured me. 
Select the grit of the stone. Sharpening stones are available with different grit sizes. For example, you can choose fine, medium and coarse stones. You should use a coarse stone followed by a fine grit if your knives are dull. If your knives have been sharpened recently or they aren't too dull, consider using a medium grit. Try to use a grit level ranging from 325 (for coarse) to 1200 (for extra fine).[3]

An important but often confusing area of sharpening is knowing when you're done with one stone and ready for the next finer grit. On coarse stones it is very easy. When you sharpen one side you will notice a burr forming on the opposite side of the edge. This burr is hard to see but is easy to feel. Very carefully feel for the burr by gently running your hand from the spine to the edge. (Do not run your finger along the knife edge from heel to tip, that's only asking for trouble!) A burr is formed when your stone removes material directly at the edge. The burr will move from one side of your knife to another as you alternate sharpening sides. Make sure you have felt the burr jump between both sides before you move on to the next finer stone. That will ensure that you have sharpened both sides effectively. The finer grits are done the same way but the burr is much smaller. On the finest grits you may not be able to notice the burr at all. Testing the knife sharpness will tell you when you're done. (Learn how you can test to see if your knife is sharp.)
Some recommended products may use affiliate links. ProHuntingKnife.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Amazon and the Amazon logo are trademarks of Amazon.com, Inc or its affiliates.
Finally, when you learn how to sharpen a pocket knife becomes reality, you'll ultimately see the difference in your blade. Every sportsman and kitchen guru should learn how to sharpen a pocket-knife the proper way without "nicking it" or "shaving the edges" off too much you end up with a short and stout blade. Consequently, selecting the proper pocket-knife sharpener is important so learning the in's and out's of how to sharpen a pocket-knife before and after using it is all in the practice as well as in the sharpener itself.

The answer to the question of how to choose a single whetstone from among the many is actually one of both purpose and expense. Indeed, as the old adage says: “You get what you pay for” – This is certainly the case with sharpening stones. In fact, as a general rule, a high quality, natural, whetstone is significantly more expensive than a man-made whetstone but, they also tend to produce a noticeably finer edge than man-made stones do. On the other hand, man-made whetstones (with the exception of diamond hones) are very affordable and, just like natural whetstones, they too are available in different grits for different stages in the sharpening process from cutting the initial edge bevel to polishing a finely honed edge.

One of the combinations of stones that I was introduced to several years ago is a unique one, it is a 500, 2,000 and 16,000 grit combination. I was apprehensive when I first tried this, that was thousands of knives ago, it works, it is fantastic combination. It is unique because the traditional way of thinking is that we should be doubling the grit sizes as we sharpen, for example, a 500 grit stone should be followed by a 1,000 grit, then 2,000 grit. This line of thought is meant to be flexible, it is a general rule only, I have broken it countless times.
Manufacturer contacted and sent a new one for replacement. Great customer service but replacement item was nicked on the corner. It was still usable so i didn't bother to ask for another replacement. I would recommend item to be shipped in another box instead of an over-sized yellow envelop which is not adequate protection. Item sharpen my knife pretty good though..
"How do I use this daunting metal rod?" I hear you ask. Well, it's not too hard, really. The best way for a beginner is to balance the steel on a surface with the tip secured by a damp tea towel. You want to get that angle right, whether it's around 15 degrees for a Japanese knife or 20 degrees on a German or French blade. Then swipe slowly down, away from you, making sure the whole blade is honed – around five swipes on each side should do. 
I really liked this whetstone! I had a Smith's pocket sharpener that could get my knife sharp enough for working around in the yard (I have an Opinel no.8). However, in doing a little research I found that the sharpener was only around 600 grit on the finest setting. So this BearMoo 1000/4000 grit looked like the perfect step up, and it turned out to be the perfect stone for me. The pictures are an accurate representation of what you get. The removable rubber base was helpful when switching from one side to the next, and it kept the stone from sliding around. The instructions say that the stone can work with either water or oil, but that water is preferred. It said to leave the stone soaking in water for five minutes, and the stone worked like a champ. I especially liked how the instructions gave you an approximate time of how long the stone takes to sharpen a knife -- it just helped give me an idea that it would take about 15-20 minutes on the 1000 grit side, and then another 10-15 minutes on the 4000 grit. Just turn on a TV show!