A: Another issue that comes up with electric knife sharpeners is how to clean them. Or if, in fact, they actually need cleaning at all. The answer to the second question is that yes, they do need to be cleaned occasionally. And by occasionally we mean once a year or so if you use them with any frequency. Obviously if you’ve only used the sharpener a few times then there’s no compelling reason to clean it, other than just wanting to keep things tidy (and there’s nothing wrong with that). So, having established that sharpeners do need to be cleaned occasionally you need to know how to do so in a safe and effective manner. It’s not complicated.
I've been using this stone for months and have started to find that, while the fine side does provide a nice sharp edge, the 400gr side is wearing my knives unevenly, which causes me to be unable to finely sharpen the entire length of the blade when moving to the fine side. The logo that is put in the middle of the 400gr side of the knife is causing more material to be removed than the rest of the blade when I'm sweeping across. I even verified this by going straight down the length of the fine side and watching the wear pattern come from the material coming off of the knife onto the stone.
As you continue to repeat strokes on the first time, eventually a tiny burr will form on the other side of the blade. To check for it, place the blade on your thumb, and pull it backwards. If the burr has formed, it should catch slightly on your thumb (with really fine grit stones, say 2000 or above, you won't feel this). This may take up to 30 or 40 strokes, and is the indication that you should switch and start sharpening the other side.
The angle on a Buck Knife is set based upon how we feel the knife will be used. Heavy use needs a strong and blunt "V" while skinning or filleting would need a deeper but more vulnerable "V". We tend to grind to 13-16 degrees per side (see illustrations). If you match the existing edge angle and hold the knife against the stone to cut evenly across the edge grind, you will produce an edge with a similar angle.
Once sufficiently wet, it's time to position the stone on something solid, so it doesn't move about during sharpening. Many come with holders, but you can just place it on a slightly damp tea towel on the table. The stone should be roughly perpendicular to your body, though Warner told me it is sometimes easier to angle it ever so slightly to the right (if you're right handed).
You might not need to spend hundreds of pounds to get the best knife sharpener, but you do need to know what you're doing. Warner gave me a crash course in the technique. As a newbie to this method, it took a while to get used to (especially since Warner handed me a knife that had never previously been sharpened) but after half an hour's practice and a little encouragement, I got the hang of it. Here's what I learned...
The word “Novaculite” is derived from the Latin word “novacula”, which means “razor stone” and is essentially a metamorphic, recrystallized, variety of Chert composed mostly of microcrystalline quartz that is found in the found in the Ouachita Mountains of Arkansas and Oklahoma and in the Marathon Uplift of Deposited in the Devonian Period and the early Mississippian Subperiod some 410 to 325 million years ago and subjected to uplift and folding during the Ouachita orogeny of the Atokan Epoch (early Pennsylvanian Subperiod), Novaculite is a very tough stone that is resistant to erosion and thus, the various layers of Novaculite stand out as ridges in the Ouachita Mountains. Thus, due to both its availability and its composition, it has been mined since ancient times for use as arrowheads and spear heads as well as in more modern times for use as sharpening stones.
In most cases, the sharper, the better. The sharpness of your edge is determined by the angle (the lower the angle, the sharper the edge) and how fine of a grit you choose for your final honing. Since you have already determined your angle many steps earlier, now you just need to know which grit you can stop at. This again depends on the use of the knife. In most cases, go all the way to the finest stone that you own as this will give you your best edge. The only exception would be a knife used to cut soft vegetables like tomatoes, as a slightly more coarse edge will provide more of a tooth pattern for easier cutting.
The composition of the stone affects the sharpness of the blade (a finer grain, usually, though not always, produces sharper blades), as does the composition of the blade (some metals take and keep an edge better than others). For example, Western kitchen knives are usually made of softer steel and take an edge angle of 20–22°, while East Asian kitchen knives are traditionally of harder steel and take an edge angle of 15–18°. The Western-style kitchen knives are generally in the range of 52–58 on the Rockwell scale, which denotes the relative hardness of a material.
The 8,000 grit Kitayama is definitely a popular 8K stone, it is my favourite, and the feedback has much to do with that. It is silky smooth and feels creamy when you use it. When reaching refinement levels of 6k and above, polished bevels/edge are inevitable, and often sought after. The level of polish from this particular stone is very beautiful, assuming that you have done some refinement prior to this but it is a wonderful 8,000 grit stone.
I recommend it as a lightweight alternative to larger stone for smaller knives. Leather necklace is comfortable and seems strong. I conditioned it for suppleness and swim with it on tightened as a choker. Stone is small, dog-tag size. I use it with water. Functional for small folder knives and multi-tools. Not useful for large fixed blades, since you can't make a long stroke. Small to grip. I use double-sided tape on one side to keep it in place on a flat rock. Not sure of grit, seems like around 1000. It took a while, but i got my old boy scout knife sharp.