This 600/1,000 grit is my second Unimi knife sharpener, the first is 2,000/6,000 grit and I love them both. Both stones together produce very sharp and well polished knives that reduce the cutting effort and save time in the kitchen. I particularly appreciate that the manufacture printed the grit number on the side of each stone - that helps use the different grits in the proper sequence from the coarser to the finer. The stone comes with a non-slip silicone/rubber base which is very handy.

As you probably have guessed, knives are easier to sharpen on longer stones. The width of the stone is less important than the length when sharpening knives. The longer stone allows for longer sharpening strokes and contributes to faster sharpening. The longer strokes mean fewer strokes across your stone, making it easier to maintain a consistent sharpening angle. As a rule of thumb, a small knife can easily be sharpened on a large stone, but a large knife cannot easily be sharpened on a small stone.
It is sometimes too confusing on understanding the right sharpener that right to our tools. Then using the chart above you can consider on what is the right stone. Green, red, yellow and blue line they consist of the most familiar and affordable models of sharpening stone to purchase. You can see the performance of each stone in the chart. Silicon Carbide, Aluminum Oxide, and Arkansas they are typically used with the oil (Oil Stones). Waterstones (Synthetic Waterstones) are generally made of Aluminum Oxide too, then people also use oil in place of water with their Waterstone or use water on their Silicon Carbide sharpening stone in place of oil. In this group, Waterstones is the most preferred because of its easy for sharpening edges in shorter time.
I've used ceramic rods, diamond plates, and leather strops for our sharpening needs. And, like most, I've tried a dozen little gimmicky sharpeners that, while some work, those that do often remove way too much material from the edge, making your blade wear down faster. I've also used oil stones, grinders and buffers for less meticulous sharpening of axes and such. These two stones from Unimi (600/1000 and 2000/6000) served as my introduction to whetstone sharpening. And I must say I like it. Though, I'm not sure of the need for investing in more expensive stones.
A nearly foolproof manual sharpener that looks like modern art, the angle that the knife is inserted into the sharpener determines how aggressive the sharpening is (yes, there is a correct angle for sharpening your knives). You can start by sharpening the knife then hone it to a fine finish in the same slot. If the knife doesn’t need sharpening, you can use this for honing only. This sharpener self-adjusts, and sharpens the knife edge to its original angle, so you don’t need to know the edge angle to sharpen the knife correctly, and there’s nothing to adjust. The tungsten carbide sharpeners will last a long time, but can be replaced when necessary.

Turning to the sharpeners themselves, we looked at aspects such as ergonomics, speed and simplicity of use, noise level and overall power (for the electric sharpeners), and build quality. We also weighed cost against performance to get a subjective measure of value. After two hours, we had clear picks for the winner and the upgrade choice, as well as an option for people who want high style along with high performance.

Many households can benefit tremendously, by owning an electric knife sharpener. Typically, these sharpeners are slightly expensive, but this isn’t the case with the Presto 08800. This particular sharpener is actually very affordable! It only weighs around 3 pounds, so it’s much lighter than other electric models. Many people will find this extremely beneficial, since it’ll allow them to transport the device and easily store it somewhere out of the way.

Silicone Carbide whetstones on the other hand, are the fastest cutting of the three types of oil stones and the stones made by Norton are called Crystolon Stones. Also they too are graded as either fine, medium, or coarse stones depending on their grit. But, although these stones will not produce an edge as fine as Arkansas Oil Stones or India Oil Stones, their fast cutting ability makes them ideal for sharpening tools as well as for cutting the initial edge bevel on extremely dull knives or repairing the edge on damaged blades. Last, because they sharpen so quickly, it a common practice to start with a coarse Crystolon Oil Stone and then progress to either a medium or fine India Oil Stone and then to finish with an Arkansas Oil Stone.
To answer an obvious question: The difference between 15 degrees and 12 degrees is so slight that a 15-degree sharpener is fine for both kinds of bevels. So if a dedicated 15-degree sharpener is all you need (that is, if you own only Asian or post-2011 European knives), we have good news: Chef’sChoice makes the otherwise identical Pronto 463, which contains a single Asian-style sharpening slot. (For the testers at Cook’s Illustrated, the Pronto 463 is the top choice among manual sharpeners.) And if you own older European knives exclusively, the company sells a dedicated 20-degree model, the Pronto 464.

Next we sharpen the opposite side of the blade. Just as you did before, sharpen the knife keeping an angle of 10' to 15'. Push the point you want to sharpen with your first, second and third fingers. While keeping the angle and pushing the point with your fingers, stroke the blade until it reaches the other edge of the whetstone. Then pull the blade back until it reaches the edge of the whetstone. This back and forth is counted as one stroke. Repeat it for about five strokes until you can see or feel some small burrs (edge curvatures).. Then move the position of your fingers to where you have not sharpened yet, and repeat this five strokes of sharpening processed from the tip to the base of the blade. When your whetstone becomes dry, occational watering during  sharpening process will also help and improve smooth sharpening.
In addition, the most prized of the natural Japanese Water Stones are quarried in the Narutaki District north of Kyoto, Japan and are commonly available as either bench stones or pocket stones in grits ranging from 120 to 12,000. On the other hand, synthetic water stones are made from Aluminum Oxide and commonly available as either bench stones or pocket stones as well in grits ranging from 220 to 8,000 and, although this is the same abrasive material used to make India Oil Stones, the difference between the two is that the binder that holds the abrasive together enables Water Stones to be much softer than India Oil Stones which, in turn, promotes faster cutting because the worn abrasive material breaks away more quickly and is replaced with fresh, sharp, abrasive material more quickly. In addition, because water stones do not become glazed or loaded with swarf like oil stones can, new abrasive particles are constantly exposed as the stone wears so it continues to cut consistently. Plus, they can be lubricated effectively with water (rather than oil which can ruin some water stones) which combines with the fine particles of abrasive from the surface of the stone to form a slurry which polishes the bevel as the stone cuts. However, it should also be noted that Water Stones do become uneven significantly faster than other types of whetstones although, their softness does make them easier to true again.
Keep in mind that the KitchenIQ 50009 Edge Grip 2 Stage Knife Sharpener is a tool for families. If you are trying to get a bit more serious about things in the kitchen, you may want to invest in a slightly more expensive tool. This KitchenIQ is a great jack of all trades, but there are better tools that accomplish individual things more efficiently.
The toughest angle to master is the angle at which you'll sharpen the edge of the knife. For a Japanese knife, that should be around 12-15 degrees. Before you reach for the protractor, a good test is to get roughly half an index finger's gap between the spine of the knife and the stone (see above). Remember to remove your finger before you start sharpening. For a Western-style knife, you want an angle of about 20°, so raise it ever-so-slightly higher.
Whether you’re purchasing a Smith’s or Zwilling J.A. Henckels pull-through knife sharpener, you will want to make sure that you look at the item carefully! Although each of these are similarly made and work the same, they’re also very different. Suffice to say, some will be better as an overall investment. Since you want to obtain the best pull-through knife sharpener, you will want to explore each of the characteristics below!

In addition, the most prized of the natural Japanese Water Stones are quarried in the Narutaki District north of Kyoto, Japan and are commonly available as either bench stones or pocket stones in grits ranging from 120 to 12,000. On the other hand, synthetic water stones are made from Aluminum Oxide and commonly available as either bench stones or pocket stones as well in grits ranging from 220 to 8,000 and, although this is the same abrasive material used to make India Oil Stones, the difference between the two is that the binder that holds the abrasive together enables Water Stones to be much softer than India Oil Stones which, in turn, promotes faster cutting because the worn abrasive material breaks away more quickly and is replaced with fresh, sharp, abrasive material more quickly. In addition, because water stones do not become glazed or loaded with swarf like oil stones can, new abrasive particles are constantly exposed as the stone wears so it continues to cut consistently. Plus, they can be lubricated effectively with water (rather than oil which can ruin some water stones) which combines with the fine particles of abrasive from the surface of the stone to form a slurry which polishes the bevel as the stone cuts. However, it should also be noted that Water Stones do become uneven significantly faster than other types of whetstones although, their softness does make them easier to true again.


Like all the other Chef’s Choice products, this too is a super-fast, super-efficient kitchen knife sharpen, ideal for regular use. This advanced electric diamond sharpener is a one-stop solution for a wide range of knives such as serrated, doubled-edged, short and straight blades. The flexible stropping discs help to engineer mirrorlike, glossy finishing touch on the edges.

It’s only the 2nd electric powered sharpener on our list but you can’t lose if you make the Chef’s Choice Trizor 15XV your sharpener of choice for double and single bevel Asian knives. This 3-stage sharpener provides something others don’t in that it converts any blade to a hyper-sharp 15 degree blade. The graduated manner by which it reaches that preferred angle also ensures the blade stays sharper, longer. And isn’t that the name of the game?


The synthetic stone is constructed out of aluminum oxide, which is a very abrasive material, but very soft. The main difference between the India and synthetic water stone is the binder that securely holds the abrasive material together. This stone will definitely offer an extremely quick cut. The way this works is the old abrasive material will break away and then will be replaced by a fresh sharp material.

The continuous diamond stone surface will work effectively when sharpening tools such as the scissors. You will have two types of diamond stones to choose from including the mono-crystalline and poly-crystalline. The diamond sharpening stone is preferable over other brands because they have a very flat surface, which will offer a perfect cut every time. 


Mastering the art of knife sharpening isn’t a cake walk. Manual knife sharpeners do provide great results but only when they’re operated correctly. There are three basic stages of the process of knife sharpening. Sharpening is the first of them. For this technique, you need a heavier sharpener stone than the knife material. The main target in this stage is to eliminate the metal from the blade to give it a terrific sharpness. Scrubbing the blade across the abrasive stone causes the metal particles to unravel. Placing the tool at a right angle is the most critical part of this process. Different angles have different effects on the edge. For sharpening, a shallow angle of 20o is considered perfect for most of the knives. A steep angle produces durable sharpness.

My order came in incomplete. I contacted the company and had a response within a couple hours. They immediately responded, researched and started the replacement process. I had my order replacement within 1 week or so. Every email was answered the same day. I so highly recommend this company. LOVE MY PRODUCT AND LOVE THE SERVICE MORE. GREAT COMPANY.


The Norton Three Stone Sharpening System gives you three different shades of sharpening with silicon carbide and aluminum oxide stone. The angle guide that is included is relatively easy to use, increasing the amount of cost benefit you will get from this unit. You also get a rotating axis that helps to keep your stones held in place for better positioning. The base also contains a reservoir that allows for easy cleaning. The length of the stone is also an advantage – you can easily sharpen the entire blade at once.
Diamond sharpening stone delivers fast cutting and sharp edges. They are tougher in material and doesn’t flatten. Therefore, it is the best way on investment if you want such of the sharpener that easy to maintain and practical to use. Diamond sharpening stone doesn’t require water other than a spill. It is also applicable to use with lubrication if you wish to.
A sharpening stone is made of particles of abrasive material that are sintered or bonded together. The blade is moved across the stone and the steel is worn away, which creates the edge. However, at the same time, the stone is also worn away to reveal new, coarse particles. As a general rule, the softer the stone, the more rapidly it will wear and will be more aggressive in use. Harder stones don’t wear as quickly.
Many Stages – Some of these machines are equipped with more than a single process, during the sharpening stage. For instance, some will have a slot for a stropping stage and another slot for the polishing stage. Others are equipped with three stages for an even more precise sharpened edge. Be sure to inspect each of these options, in order to find one that peaks your interest and suits your preferences.
The continuous diamond stone surface will work effectively when sharpening tools such as the scissors. You will have two types of diamond stones to choose from including the mono-crystalline and poly-crystalline. The diamond sharpening stone is preferable over other brands because they have a very flat surface, which will offer a perfect cut every time. 
It looks like it can be a Sci-Fi film prop. This is a 2 stage type of sharpening system. You'll get a non slip cushion with it which is at the bottom offering stability for the user. It's ergonomic handle provides a comfortable and easy grip. This cushion offers the stability needed when sharpening and polishing your pocket knife to it's absolute razor sharpness. The sharpener does the work as you hold down the grip and simply place your pocket knife to get sharpened by the motions of the ceramic and diamond sharpener wheels. Simply run your dull knives through the device and you'll get the results you've been looking for. This one will definitely help you when you learn how to sharpen a pocket knife on the Priority Chef.
Before starting the sharpening process, you should put some honing solution to the surface. Water can also be used as a substitute but you don’t need to use a lot of them as a small amount would be enough for it. The absent of lubricant and water will cause a damage to your stone. The angle guide will help you to keep the blade at a perfect angle so that you can get the best output.

A honing rod (also known as a honing steel, knife steel, or sharpening steel) is also highly recommended. These are not sharpeners, although they are often thought of that way. Rather, a honing rod helps keep a blade’s edge keen between sharpenings by straightening out the tiny dings and dents caused by everyday slicing and chopping. Honing is a simple and fast process—it takes just a few seconds—and it can extend the life of a sharp edge for weeks or even months. Eventually, however, the edge gets rounded over and dull; then it’s time for a complete resharpening.


Believe it or not the company have put a bit of effort into refining the look of their product to make it more aesthetically appealing. Whether or not they’ve succeeded we’ll let you decide. Once you get accustomed to the Classic II however the results are undeniable and the whole thing will make perfect sense. Use it on your kitchen knives, hunting knives, utility knives and more and enjoy the same high quality finish every time.
After several uses the Kamikoto is proving itself to be better than expected. As a professional I use different knives all the time and in fact have several thousand dollars worth of very fine blades of various manufacture. As it stands right now, if I could pick only one knife from all of them, I would take the Kamikoto. Fish, vegetables, raw meat, cooked meat, it handles them all very well and is a pleasure to use because of excellent balance and weight. And the edge… magnificent. Care and careful sharpening will be important, but then it always is with the finest of things. I would unhesitatingly recommend this product to people who appreciate the best. This is not a knife for fools or clumsy people. Buy, use, enjoy. And to the people at Kamikoto; “Thank You for making such a beautiful thing!”
×