The DuoSharp Plus stones are nicely sized at 8” long by 2 5/8” wide and have two grits on each stone to maximize value. The Plus in the name refers to an area of continuous grit in the otherwise interrupted grit surface of the stone. This area is for sharpening edges with fine points that might be difficult on the interrupted surface. A coarse/fine DuoSharp Plus stone is a good single stone to start a sharpening toolkit.
An important but often confusing area of sharpening is knowing when you're done with one stone and ready for the next finer grit. On coarse stones it is very easy. When you sharpen one side you will notice a burr forming on the opposite side of the edge. This burr is hard to see but is easy to feel. Very carefully feel for the burr by gently running your hand from the spine to the edge. (Do not run your finger along the knife edge from heel to tip, that's only asking for trouble!) A burr is formed when your stone removes material directly at the edge. The burr will move from one side of your knife to another as you alternate sharpening sides. Make sure you have felt the burr jump between both sides before you move on to the next finer stone. That will ensure that you have sharpened both sides effectively. The finer grits are done the same way but the burr is much smaller. On the finest grits you may not be able to notice the burr at all. Testing the knife sharpness will tell you when you're done. (Learn how you can test to see if your knife is sharp.)

Selecting the right sharpening angle is the next step in sharpening. For more detailed instructions on selecting the right angle, try reading this article. Regardless of the method of sharpening, a appropriate angle should be selected. This angle doesn't need to be exact but following some general guidelines is a good idea. Most knife manufacturers recommend a roughly 20 degree angle. Depending on the use of your knife, you can move up or down from that angle. A fillet or slicing knife is never used on anything hard so an angle a few degrees less will produce a sharper edge. On the other hand, a survival knife with various uses can benefit from a more durable edge a few degrees larger.

If in doubt or just learning, a safe bet is a set of quality synthetic stones. They’re the easiest to use, require the least maintenance and are the most forgiving. If you’re just starting out we highly recommend the Naniwa Sharpening Stones. They’re excellent quality, reliable, durable and no soaking time is required. For advanced users we recommend the Naniwa Pro sharpening stones or Kaiden Ceramics.
Here is what you need to get started and it does not begin with the tangibles. Success will come quickly if you understand and can visualize what it is you are attempting to do, what has to happen to make a knife sharp. My experience is with Japanese Water Stones but the same will hold true for other methods. I do not recommend pull through gadgets or electric grinders of any type by the way, I am opposed to those methods although I understand the desire to try everything out… remember, I thought I needed everything and I thought everything worked.
The truth is that there is no one recommendation that we can make that will meet everyone’s needs. Every sharpener’s needs are different and every sharpening toolkit will be different. In order to help beginning sharpeners get started with good sharpening stones to build around, we need to understand their individual needs. So with that in mind, let’s look at the basic needs of a beginning sharpener.
Table mounted device – Typically the manual powered table mounted sharpener looks virtually identical to the electric powered sharpener with a slot for each stage. Where they differ is that each slot in the manual powered sharpener has only one groove and you pull the blade through this groove toward you to sharpen the blade. Once the blade is sufficiently sharp you place it in the honing groove to refine the edge and pull it toward you again several times. If there is a third, cleaning, stage you repeat the process for that stage as well.

Silicone Carbide whetstones on the other hand, are the fastest cutting of the three types of oil stones and the stones made by Norton are called Crystolon Stones. Also they too are graded as either fine, medium, or coarse stones depending on their grit. But, although these stones will not produce an edge as fine as Arkansas Oil Stones or India Oil Stones, their fast cutting ability makes them ideal for sharpening tools as well as for cutting the initial edge bevel on extremely dull knives or repairing the edge on damaged blades. Last, because they sharpen so quickly, it a common practice to start with a coarse Crystolon Oil Stone and then progress to either a medium or fine India Oil Stone and then to finish with an Arkansas Oil Stone.
Actually, the company contacted me to make sure I received the stones and that I was happy with them. Excellent service. The stones are great! I'm pretty much a novice so the clear instructions that came with the stones and the eBook instructions were wonderful. The eBook had quality pictures demonstrating the use of the stones and the written instructions were clear and to the point. Within minutes of opening the box I had the stones figured out and sharpening my AF survival knife, my pocket knife and a couple of my wife's kitchen knives...which included a very expensive chef's knife. Very satisfied with this product and highly recommend it.
Hi Caide, our most popular stone at the moment is our Grunwerg 1000/3000 grit whetstone from speaking to our customers it’s definitely down to the pretty competitive price, but also they have said that the finish on the knife is just as good as some of our more expensive ones, the main difference is it doesn’t seem to last as long. For one that does last and leave a good finish then our Minosharp 1000 grit whetstone is also popular.
Manufacturer contacted and sent a new one for replacement. Great customer service but replacement item was nicked on the corner. It was still usable so i didn't bother to ask for another replacement. I would recommend item to be shipped in another box instead of an over-sized yellow envelop which is not adequate protection. Item sharpen my knife pretty good though..
Very interesting. If you work flat, 45 degree is what I was taught. Love the wet stones, especially the oiled ones. The nice thing about the leather part, is the mirror finish on a razor sharp blade which is a must if doing fine wood working, carving etc. A rough blade simply does not have the fine detailed dexterity. I find that the oiled sandpaper can work great as well, but found that the refined clay bars (white refined fired clay rounds and flats etc) does a wonderful job of keeping those razor edges refined, smooth as possible and then one can high polish them for smooth cutting. Believe me, when working wood for a flute, one wants that refined edge.! Learning how to hone a blade on a flat surface teaches one to work outside without a table/wall handy too...:) But we all have to start somewhere!:) Anyway, great stuff and a great start for those who want more from their tools!:) Cheers!
You've acquired a good chef's knife, you're using it almost daily to make tasty dinners for the family, and it's stored in a nice knife rack or a magnet for safekeeping. So why stop there? Keeping that knife's edge fine will make cooking not only safer but, let's face it, much more fun. Whether you've spent £150 on a high-end knife or under a tenner on a dinky paring knife, keeping it sharp is crucial. 
Put the pointed, narrow end of the sharpener up against the open end of the gut hook. The narrow, pointed end of the sharpener should face in toward the thickness of the blade, away from the edge of the gut hook. Match the angle of the sharpener to the original edge angle. This will maintain the correct sharpening angle and prevent you from getting cut by the blade tip. Hold the same angle when sharpening each side of the gut hook.
Silicone Carbide whetstones on the other hand, are the fastest cutting of the three types of oil stones and the stones made by Norton are called Crystolon Stones. Also they too are graded as either fine, medium, or coarse stones depending on their grit. But, although these stones will not produce an edge as fine as Arkansas Oil Stones or India Oil Stones, their fast cutting ability makes them ideal for sharpening tools as well as for cutting the initial edge bevel on extremely dull knives or repairing the edge on damaged blades. Last, because they sharpen so quickly, it a common practice to start with a coarse Crystolon Oil Stone and then progress to either a medium or fine India Oil Stone and then to finish with an Arkansas Oil Stone.
Why spend hundreds of dollars on a knife sharpening machine when you can get your knives razor sharp for the price of a cheap necktie? It won’t take more than a few practice sessions to learn how to get your knives professionally sharp with the Lansky 8” Ceramic Sharp Stick. This device is simplicity incarnate and yet it does the job of electric sharpeners costing many times more.
We have been helping customers find the right sharpeners for more than a decade. Selecting a sharpener can be difficult if you're not sure what you need. Our staff is trained to listen to your needs and to help you find the right sharpener the first time. We understand that it may be your first time sharpening, so we're available to help you if you have questions. Even if you're already a sharpening professional, our staff is available to answer your tough questions. We use what we sell, so you can be assured that when you purchase from us, we're able to help you with your sharpener.
The final Chef’s Choice sharpener on our list is the 316 Diamond Sharpener. Like the 15XV the 316 is at its best when used to sharpen Asian-style knives and it does so with unflinching effectiveness and speed. This is a compact, 2-stage electric sharpener that produces the 15 degree edge so favored in Asian cutlery. Ideal for the preparation of sashimi or sushi.
The Sunrise Pro doesn’t have the pedigree of some other knife sharpeners on our list but it performs as advertised and that’s all that matters. For a relative song you get to restore all the knives, steak knives, cleavers in your kitchen to near pristine condition. It’s easy to use and the nice strong suction cup on the bottom means you can put the band aids away.
A great sharpener for all your kitchen knives the CS2 also makes a smart addition to the gear when you’re going away on a family camping trip. It will also do a bang-up job on your hunting, pocket, boning knife and more. As mentioned it does require just a bit of getting used to in order to achieve optimal results but nothing too involved. A simple, effective, no-frills sharpener.
Beginning on the right side of the knife, move from tip to heel and heel to tip, then flip the knife and repeat. For the left side, it’s opposite—start at the top of the stone to reach the heel area completely. So, you will move from heel to tip and then tip to heel. Remember to apply and release pressure as you did earlier, exactly the same as in Step 2, but with light, refining pressure. 

Once sufficiently wet, it's time to position the stone on something solid, so it doesn't move about during sharpening. Many come with holders, but you can just place it on a slightly damp tea towel on the table. The stone should be roughly perpendicular to your body, though Warner told me it is sometimes easier to angle it ever so slightly to the right (if you're right handed). 

A: When it comes to the best knife sharpeners used in a domestic setting the abrasives used to sharpen the blade should last for quite a few years. When they do eventually wear out many of the best manufacturers will refurbish them for you, typically for a nominal fee. Again, however, unless you are using the sharpener on a daily basis (and there is virtually no reason the average person would do this), the sharpener should last for many years before ever needing service.
I like the fact that there are two different grits (can be seen as two colors). the black rubber feet stick to the kitchen granite top like glue. The 1000 does a pretty good job of getting a knife roughly there and the 4000 puts on a fine polish for razor a sharp edge. I would go the extra step of stropping the knife after the grinding operation for an extra sharp edge.
There will be a drawer that extends into the mechanism under the abrasives. Any detritus from the sharpening process drops into this drawer. Exactly where the drawer is located will differ from sharpener to sharpener but it shouldn’t be hard to find. Remove the drawer flick any material into the wastebasket and then wipe out the drawer with a damp cloth or tissue. You may want to use work gloves and goggles to protect your hands and eyes from any loose metal shavings. Once the drawer is clean and dry replace it. The exact means by which the sharpening mechanism itself is cleaned will vary from manufacturer to manufacturer. Consult your owners guide for specific details. Make sure you don’t introduce any grease or other lubricants into the sharpener unless specifically directed to do so by the owner’s manual. Also, the outside of the sharpener should come perfectly clean with just a damp cloth. Avoid using commercial cleaners or abrasives of any kind.
Very handsome and functional. The leather that makes up the necklace is high quality and the knot they use is seldom seen. I was able to touch up my bark River gunny sidekick with it( m4 steel at 62-64 hrc!), And that is saying something. Haven't tested the fish hook groove, because I don't generally fish in the winter, but I'm looking forward to trying it out
✅ PREMIUM QUALITY : Our products have been inspected by a reputable third party inspection company. Each product has been checked,put under a durability and functionality test before shipped to you. NO COMPROMISE on quality! This simple-yet-unparalled award winning tool is used by everyone from stay at home moms to various professionals. Don’t forget to buy this as a PERFECT GIFT for your family & friends.
For instance, American Novaculite (aka Washita and Arkansas Stones) is a form of metamorphic Chert that produces some of the best known and best loved natural whetstones in existence. Then, there is a form of Belgian Coticule which has been known for providing extra-keen edges since Roman times and, there is a Japanese Siliciclastic sedimentary stone (aka Japanese Water Stones) which consist of a fine silicate particles suspended in a clay matrix. Plus, there are also various types of man-made whetstones available such as Silicon Carbide (aka Crystalon) stones and Aluminum Oxide (aka India Stones) as well as a synthetic Corundum (aka Ruby) rod and Aluminum Oxide impregnated ceramic rods as well as several different types of diamond hones.
Once you’ve decided to start sharpening your kitchen knives with a sharpening stone, you’ll need to take the necessary steps to actually get going. These steps include finding and buying the best sharpening stone for use at home, learning the basic technique involved in doing the sharpening, and then practicing enough times to get it right. (For the sake of the knives, we don’t recommend using your best kitchen knives for practice!)
Table mounted device – Typically the manual powered table mounted sharpener looks virtually identical to the electric powered sharpener with a slot for each stage. Where they differ is that each slot in the manual powered sharpener has only one groove and you pull the blade through this groove toward you to sharpen the blade. Once the blade is sufficiently sharp you place it in the honing groove to refine the edge and pull it toward you again several times. If there is a third, cleaning, stage you repeat the process for that stage as well.

It helps you get the knack for a consistently correct angle BUT the idea falls apart a bit when it comes to the curve and taper part of the knife and if your knife has an excessively narrow (slicer/boner) or wide (cleaver) width. It will also mark up the sides of your knife which may bother some who are obsessed with the cosmetic appearance of their $150+ Japanese knives--I could care less.

Grit choices should fall in line with the steel used to make the knives you plan to sharpen. If your knives are all European, relatively soft steel knives, then you could finish off your knives at the 1,000 – 2,000 grit level. There is a lengthy explanation regarding this topic but suffice it to say that at 2,000 grit, these knives can be made extremely sharp.
Low Grit Stones: A sharpening stone with grit number less than a 1000 is generally used for knives and tools that are damaged. If your blade has any nicks or chips in the blade, the stones will take care of them in a jiffy! They usually have a coarse side for nicks and chips, with the other side for general sharpening. Even if the knife’s edge has become totally blunt, the stone will re-sharpen it perfectly.
One of the combinations of stones that I was introduced to several years ago is a unique one, it is a 500, 2,000 and 16,000 grit combination. I was apprehensive when I first tried this, that was thousands of knives ago, it works, it is fantastic combination. It is unique because the traditional way of thinking is that we should be doubling the grit sizes as we sharpen, for example, a 500 grit stone should be followed by a 1,000 grit, then 2,000 grit. This line of thought is meant to be flexible, it is a general rule only, I have broken it countless times.
Dull knives aren't just annoying — they can be downright dangerous. Keep yours in top shape with the Sharp Pebble Knife Sharpening Stone. It has a #1000 grit side for dealing with dull edges, and a #6000 side for honing to razor-like sharpness. It sits inside a silicone base, inside a non-slip bamboo base, and comes with an angle guide that slides over the spine, ensuring that even beginners can set a proper edge.

We have been helping customers find the right sharpeners for more than a decade. Selecting a sharpener can be difficult if you're not sure what you need. Our staff is trained to listen to your needs and to help you find the right sharpener the first time. We understand that it may be your first time sharpening, so we're available to help you if you have questions. Even if you're already a sharpening professional, our staff is available to answer your tough questions. We use what we sell, so you can be assured that when you purchase from us, we're able to help you with your sharpener.


You’ll know you’re reached a stopping point when you can feel the slight catch of the bevel on the edge of the blade, by carefully running your finger in the direction of the blade, or by cutting through a sheet of paper. When the knife cuts cleanly through the paper, it’s time to hone the blade. Read our guide for more information about honing vs sharpening.
But it's a different type of sharp, according to Joe Authbert, product development manager at ProCook. "What it does is add tiny little micro-serrations onto the edge of the blade." But fear not - your smart knife won't end up looking like a bread knife, as you'll be hard-pressed to spot the serrations. "If you looked at it under a microscope, on the cutting edge, there are these little lines that generate the sharpness, rather than a waterstone which is a smooth sharp edge," says Authbert. 
I recommend it as a lightweight alternative to larger stone for smaller knives. Leather necklace is comfortable and seems strong. I conditioned it for suppleness and swim with it on tightened as a choker. Stone is small, dog-tag size. I use it with water. Functional for small folder knives and multi-tools. Not useful for large fixed blades, since you can't make a long stroke. Small to grip. I use double-sided tape on one side to keep it in place on a flat rock. Not sure of grit, seems like around 1000. It took a while, but i got my old boy scout knife sharp.
As you continue to repeat strokes on the first time, eventually a tiny burr will form on the other side of the blade. To check for it, place the blade on your thumb, and pull it backwards. If the burr has formed, it should catch slightly on your thumb (with really fine grit stones, say 2000 or above, you won't feel this). This may take up to 30 or 40 strokes, and is the indication that you should switch and start sharpening the other side.
Freshly brewed beer tastes great, but nailing the brewing process is tough. The LG HomeBrew Beer Machine makes it easy. This countertop gadget uses single-use capsules containing malt, yeast, hop oil and flavoring and an optimized fermentation algorithm to let you brew beer with a single button press, creating up to five liters of suds every two weeks. Offered in the initial launch are a hoppy American IPA, American Pale Ale, full-bodied English Stout, Belgian-style Witbier, and Czech Pilsner. The machine will be on display at CES 2019, a perfect spot for finding thirsty test subjects.

Some recommended products may use affiliate links. ProHuntingKnife.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Amazon and the Amazon logo are trademarks of Amazon.com, Inc or its affiliates.
I enjoy these stones so much that the feedback is not a deterrent at all for me, I don’t even think about it. The results are always nothing but top notch, they deliver exactly what I want, some of the sharpest knives I have ever produced were sharpened on Shapton Glass stones. They may be thinner but they last a very long time, they are easy to maintain as well, 

Everten is Australia's leading online kitchenware retailer. A passionate Australian family business, we pride ourselves on having the best range available, stocking over 10000 products from the world's leading brands matched with the best service. As the very first online kitchenware retailer to become a Google Trusted Store in Australia, you know that you can trust us to deliver quality kitchenware at unbeatable prices with full product warranties to your door for just a flat rate of $8.90 anywhere in Australia. Read more about us
×