Place an old coffee mug upside down so that the bottom of the mug is exposed to the air. In a pinch, a coffee mug can serve as a surprisingly effective sharpening tool if you don't have any fancy equipment. The ceramic material of a mug is a material coarse enough to get good results. Indeed, some honing rods even use ceramic material to keep a blade homed in between sharpenings.
Unfortunately, the arrays of modern whetstone can be bewildering to the inexperienced sharpeners that so often times many of them end up with a crap or wrong decision on stone type for their utensils. The most difficult to determine is whether the whetstone is fake or fabricated with low quality of materials. To avoid this you can only go for the reliable brand of a whetstone.
Your immediate goal is to raise a burr on the side of knife opposite to the side you are sharpening and depending on the steel, the grit of stone and how you are doing, it will be either a very quick process or it will seem like it takes an eternity. Patience here will reward you, believe me. The sharpening process is incomplete with no burr creation on your first stone. (Yes, it is possible to stop at that magic moment without the burr forming but we are not there yet, we don’t even need to go there, ever, I am just mentioning it so those gifted sharpeners will be happy) . Think of the burr as the debris that is making the knife dull being forced down the blade towards the edge and over to the other side of the by your sharpening prowess. You form the burr, that knife will get sharp, no burr, you just need to look at your work. A Loupe is handy here, an inexpensive magnifying device with a light that allows you to see the edge very well, if you are not forming a burr, you are not reaching the edge. (Having a loupe also makes you look cool and scientific, like a Sharpologist).
Why spend hundreds of dollars on a knife sharpening machine when you can get your knives razor sharp for the price of a cheap necktie? It won’t take more than a few practice sessions to learn how to get your knives professionally sharp with the Lansky 8” Ceramic Sharp Stick. This device is simplicity incarnate and yet it does the job of electric sharpeners costing many times more.
The paper test - Remove your knife from the sharpener. Grab a piece of notebook paper and hold it vertically in your hand so that one edge is facing straight up. Now take the knife and push it down against this edge. If the blade cuts through without hesitation it’s sharp. If the paper simply crumples beneath the blade instead of cutting the blade needs a bit more work.
Low Grit Stones: A sharpening stone with grit number less than a 1000 is generally used for knives and tools that are damaged. If your blade has any nicks or chips in the blade, the stones will take care of them in a jiffy! They usually have a coarse side for nicks and chips, with the other side for general sharpening. Even if the knife’s edge has become totally blunt, the stone will re-sharpen it perfectly.
Again, burr formation is critical to success and if you are using a 1,000 grit stone on a dull knife, you may be there for a while but it will form. If you are grinding on one side for more than 3-4 minutes, flip the knife and work the opposite side, always feeling for a burr with your thumb on the opposite side to which you are working on. Remember, the fatigued metal is being forced down the blade towards the edge of the edge by your actions and the abrasive properties of the stone.
A: We’re all told that a sharp knife is safer than a dull knife yet most everyone knows that merely touching a sharp knife can often result in a painful cut while we can wrap our hand around a dull blade with little worry. So why would anyone in their right mind claim that a sharp one is safer than a dull one? To a certain extent it’s a matter of semantics for sure, because there is no denying you have to be extremely careful around really sharp knives. But at the same time there is a very good reason to consider a dull knife to be more of a safety hazard than a sharp knife.
An important but often confusing area of sharpening is knowing when you're done with one stone and ready for the next finer grit. On coarse stones it is very easy. When you sharpen one side you will notice a burr forming on the opposite side of the edge. This burr is hard to see but is easy to feel. Very carefully feel for the burr by gently running your hand from the spine to the edge. (Do not run your finger along the knife edge from heel to tip, that's only asking for trouble!) A burr is formed when your stone removes material directly at the edge. The burr will move from one side of your knife to another as you alternate sharpening sides. Make sure you have felt the burr jump between both sides before you move on to the next finer stone. That will ensure that you have sharpened both sides effectively. The finer grits are done the same way but the burr is much smaller. On the finest grits you may not be able to notice the burr at all. Testing the knife sharpness will tell you when you're done. (Learn how you can test to see if your knife is sharp.)
I purchased this set together with the 400/1000 grit stone assuming that some of my knives were quite dull and would need work on a coarse grit stone. Premium Whetstone Sharpening Stone 2 Side Grit 400/1000 | Knife Sharpener Waterstone with NonSlip Rubber Base & Flattening Stone. This is my first wetstone. First off I tried to sharpen my Chicago Cutlery boning knife. This knife is nearly thirty years old, has been abused in may ways and was quite dull. It was very difficult for me to get a burr on this blade, which I attribute to poor technique. Next I moved on to my Henckels Professional S paring and chef's knives. The paring knife was moderately sharp and was modestly improved after working over all three grits of stone. It would cut paper but again it was difficult to develop a burr with this blade. Undaunted I switched to the chef's knife. This knife is twenty years old and has never been professionally re-sharpened. I have sharpened it twice with a Lanksey sharpening system which marred the finish but did put a good edge on the blade. Lansky Standard Coarse Sharpening System with Fine Hones. The chef's knife was moderately dull and had several pits visible on the cutting surface. I modified my technique for passing the knife over the stone and worked the chef's knife over the 400 grit stone aggressively and eventually I was able to get a burr to form from the tip of the knife all the way to the handle. From there it was a simple process of reforming the burr on the 1000 grit stone and then finishing on the 6000. After sharpening, the chef's knife easily and cleanly slices a tomato with very light pressure and is in my opinion very sharp. Not sushi knife sharp but more than enough for the chopping and slicing I expect of it. I'm looking forward to going back and working both the boning knife and the paring knife over again. Don't expect a good result from this product the first time you use it. Watch videos on using a wetstone, expect to spend at least twenty minutes per knife at first, and practice forming a burr. If you can form a burr, you will be able to successfully sharpen your knife.