Why, then, do so many of us shy away from the task? To put it bluntly, it's because it's a rather daunting process for the beginner. Your image of knife sharpening may consist of a hyper-masculine chef slashing away violently at a steel rod (we're looking at you, Gordon). Conversely, you might have seen cooks meticulously and methodically stroking their blade up and down a Japanese waterstone with more intricate attention to detail than a Flemish landscape. 

Next we sharpen the opposite side of the blade. Just as you did before, sharpen the knife keeping an angle of 10' to 15'. Push the point you want to sharpen with your first, second and third fingers. While keeping the angle and pushing the point with your fingers, stroke the blade until it reaches the other edge of the whetstone. Then pull the blade back until it reaches the edge of the whetstone. This back and forth is counted as one stroke. Repeat it for about five strokes until you can see or feel some small burrs (edge curvatures).. Then move the position of your fingers to where you have not sharpened yet, and repeat this five strokes of sharpening processed from the tip to the base of the blade. When your whetstone becomes dry, occational watering during  sharpening process will also help and improve smooth sharpening.

At age 10, Terada learned the basics of sushi from his father and then went on to attend RKC Chef's School in Kochi, Japan from 1987-1989. He soon earned a nickname for his fast knife, attention to detail, divine presentation and ability to create new dishes and accents based on traditional Japanese cuisine. After graduating RKC Chef School, he was called to serve under Master Chef Kondo at Yuzuan restaurant in Kochi, Japan from 1989-1992. Mr. Kondo is the master of Kansai style cooking, considered to be the high-end of Japanese cuisine. Terada earned the title Master Sushi Chef by becoming the standing head sushi chef & can serve Fugu (Japan Licensed) to the public.
When you want to learn how to sharpen a pocket-knife on a sharpening stone, your pocket knife isn't going to get sharp in one stroke. You have to have at least a stone bar that's the minimum of 2x6 inches in measurement. In general, it'll help make the sharpening of the blade easier. When you sharpen it on a stone, you have the three main options: ceramic stones, whetstones, and diamond stones.
Whetstone has two different sides of grain for sharpening and polishing knife edges. These softer Japanese stones have several advantages over harder stones. Because they are softer, they do not become glazed or loaded with detritus. Plus, they are lubricated effectively with water rather than oil, but can be used with either. Submerge the stone in water for about 5 - 10 minutes. Continue to apply water while sharpening with the Whetstone Cutlery Two sided Whetstone Sharpening Stone. The stone releases small particles during the sharpening process; this powder in combination with water allows the sharpening. After a while you will notice a small burr at the edge. Now repeat the same process on the other side of the blade. Finally, turn the stone over and repeat the procedure, this time using the finer grit of the stone. In order to remove the remaining burr, pull the blade at an angle over the stone. Rinse the stone and clean off the grinding residue. Clean your knife with hot water.
Japanese water stones – both natural and synthetic – are known for their superior sharpening performance, not only for Japanese tools, but also on their Western equivalents. The loosely bonded abrasive grit is washed out very quickly, as it blunts during the sharpening process; this exposes new, sharp, particles that can get to work on the blade. Water stones are lubricated only with water! Never use oil!

In addition, the most prized of the natural Japanese Water Stones are quarried in the Narutaki District north of Kyoto, Japan and are commonly available as either bench stones or pocket stones in grits ranging from 120 to 12,000. On the other hand, synthetic water stones are made from Aluminum Oxide and commonly available as either bench stones or pocket stones as well in grits ranging from 220 to 8,000 and, although this is the same abrasive material used to make India Oil Stones, the difference between the two is that the binder that holds the abrasive together enables Water Stones to be much softer than India Oil Stones which, in turn, promotes faster cutting because the worn abrasive material breaks away more quickly and is replaced with fresh, sharp, abrasive material more quickly. In addition, because water stones do not become glazed or loaded with swarf like oil stones can, new abrasive particles are constantly exposed as the stone wears so it continues to cut consistently. Plus, they can be lubricated effectively with water (rather than oil which can ruin some water stones) which combines with the fine particles of abrasive from the surface of the stone to form a slurry which polishes the bevel as the stone cuts. However, it should also be noted that Water Stones do become uneven significantly faster than other types of whetstones although, their softness does make them easier to true again.