Selecting the proper coarseness for your sharpening stone is an important first step in sharpening your knife. Not every knife needs to start at the coarsest stone you have, on the other hand a very dull knife can not be sharpened on only your finest stone. Starting with the proper coarseness will ensure that you achieve the edge you need quickly. If your knife is very dull or has a nicked blade, start with your coarsest stone. The coarse stone removes material quickly so a poor edge can be refined quickly. However, the coarse stone must be followed up with your finer stone to refine the edge. If your knife is only slightly dull and just needs a quick touch up, starting at a medium or fine stone can save you time. Starting on a fine stone requires fewer steps but must only be used on an edge requiring little work.

A: That depends almost entirely on how often you use them. If you are a professional chef who uses his or her knives every day then you should hone them every time you use your knives. But honing has its limits and over time your edge is going to become dull no matter what. Therefore your knives will need to be sharpened at least several times a year. Some chefs, in fact, will use a whetstone on an almost daily basis in order to ensure their knives are always razor sharp. Most of us, however, are not professional chefs and may not even touch our kitchen knives for days at a time. In that case, it’s probably a good idea to hone the edge after every couple of uses and have your knives sharpened once a year.
In recent years, some whetstone manufacturers have started producing ceramic whetstones made from hard, ceramic, powders that are mixed with Aluminum Oxide and then sintered to form a solid. But, rather than using oil or water to lubricate the whetstone, ceramic whetstones are meant to be used without lubrication and thus, they provide a significant advantage for chefs who need to keep their knives sharp but, who do not have either the room or time for using a bench water stone. Thus, they are commonly available as either bench stones, pocket stones, round rods, or triangular rods.
This is a good quality stone for a beginner looking to learn about hand sharpening knives and blades. It holds up well, especially for the price point. New sharpeners are prone to gouging and scratching stones, pushing too hard, etc, and this stone handles the abuse nicely. The no slip base is very effective at cementing the stone in place, which is a critical safety feature.
Clean the knives and stone. As soon as you've finished sharpening your knives, wash and dry the blades. You should also clean the stone according to the manufacturer's instructions. For example, if you have an oil stone, you might need to scrub it occasionally with a stiff fiber brush and soak it in oil. For a water stone, wash off any of the residue and store it in a dry cloth until you need to use it again.[11]
Unfortunately, the arrays of modern whetstone can be bewildering to the inexperienced sharpeners that so often times many of them end up with a crap or wrong decision on stone type for their utensils. The most difficult to determine is whether the whetstone is fake or fabricated with low quality of materials. To avoid this you can only go for the reliable brand of a whetstone.
Thank you so much for your unbelievably quick service and delivery. I placed my order online and within pretty much one day the package is waiting on my door step. My order was also filled perfectly, no mistakes. I sure know where I will be purchasing all my sharpening supplies in the future. Great business practice you have. Please never change it.
Next we sharpen the opposite side of the blade. Just as you did before, sharpen the knife keeping an angle of 10' to 15'. Push the point you want to sharpen with your first, second and third fingers. While keeping the angle and pushing the point with your fingers, stroke the blade until it reaches the other edge of the whetstone. Then pull the blade back until it reaches the edge of the whetstone. This back and forth is counted as one stroke. Repeat it for about five strokes until you can see or feel some small burrs (edge curvatures).. Then move the position of your fingers to where you have not sharpened yet, and repeat this five strokes of sharpening processed from the tip to the base of the blade. When your whetstone becomes dry, occational watering during  sharpening process will also help and improve smooth sharpening.
The whetstone is the most popular for sharpening pocket knives (or knives). But, before  you go into the sharpening, you must prepare the whetstone beforehand.  Don't worry, it's quite easy. The majority used can be done by dipping the stone in water for about 15 minutes. Regardless of what type of whetstone you use, never use it while it's dry. It's important for a clean sharpening. Using mineral oil is another way to prepare a whetstone. It'll absorb into it once you begin putting the right amount on the surface. How you will determine how much to put is to ensure a "thick film" is lathered across the entire surface. This is critical when you learn how to sharpen a pocket knife.
Honing steels are another story altogether. Honing steels are those instruments that look light a saber (light or otherwise) which you use to gussy up the edge of the blade periodically before using it. These do wear out every few years or less, depending on how often you use them. If you are unsure whether your honing steel is worn out run your finger around it. If it feels smooth all the way around then it’s time for a replacement. Not to worry though, they’re really affordable. One thing you may want to keep in mind about honing steels is that they typically won’t do much to hone the edge of some super hard knives, such as Japanese Global brand knives.
Once the burr is removed, it's time to test the sharpness with paper. Hold a piece of newspaper at about 45°, with a bit of tension, and slash lightly with each point of the blade. If it cuts through easily, your knife's sharp. Warner speedily lacerated his newspaper, but I of course struggled. There is an element of technique involved, he reassured me. 
Hold the knife in your right hand (or left) with your index finger along the spine of the knife and be comfortable, hold it tight enough so it doesn’t move as you sharpen but you don’t need a death grip on it. Wear shoes and if possible stand on a mat that will absorb the impact of the knife if you drop it. (You won’t drop it but be safe…..move your feet if you drop it!).
Heres why I wasn't impressed at first. I only used it for a few minutes on each side, which resulted in nothing. I watched a video online with a master chef using his stone, and he sharpened his knife for 10 minutes on each stone before moving up to a finer grit. I took this hint, and used sharpened my knife on each side of this stone for 10 minutes, which led to perfection.

Now you may wonder, if a finer stone produces a better cutting edge why do I need a coarse stone at all? The answer is that finer stones work much more slowly than coarse ones. The amount of metal a fine stone removes with each pass is much less than what a coarse stone removes. If you have an edge with a good shape to it from a coarse stone, this is not a problem because the fine stone doesn’t have to remove much metal to improve the edge. If the edge is dull, it will take many times longer to reshape it with a fine stone than it would with a coarse one.
Historically, there are three broad grades of Japanese sharpening stones: the ara-to, or "rough stone", the naka-to or "middle/medium stone" and the shiage-to or "finishing stone". There is a fourth type of stone, the nagura, which is not used directly. Rather, it is used to form a cutting slurry on the shiage-to, which is often too hard to create the necessary slurry. Converting these names to absolute grit size is difficult as the classes are broad and natural stones have no inherent "grit number". As an indication, ara-to is probably (using a non-Japanese system of grading grit size) 500–1000 grit. The naka-to is probably 3000–5000 grit and the shiage-to is likely 7000–10000 grit. Current synthetic grit values range from extremely coarse, such as 120 grit, through extremely fine, such as 30,000 grit (less than half a micrometer abrasive particle size).[citation needed]
One of the most well-regarded natural whetstones is the yellow-gray "Belgian Coticule", which has been legendary for the edge it can give to blades since Roman times, and has been quarried for centuries from the Ardennes. The slightly coarser and more plentiful "Belgian Blue" whetstone is found naturally with the yellow coticule in adjacent strata; hence two-sided whetstones are available, with a naturally occurring seam between the yellow and blue layers. These are highly prized for their natural elegance and beauty, and for providing both a fast-cutting surface for establishing a bevel and a finer surface for refining it. This stone is considered one of the finest for sharpening straight razors.[citation needed]

The word “Novaculite” is derived from the Latin word “novacula”, which means “razor stone” and is essentially a metamorphic, recrystallized, variety of Chert composed mostly of microcrystalline quartz that is found in the found in the Ouachita Mountains of Arkansas and Oklahoma and in the Marathon Uplift of  Deposited in the Devonian Period and the early Mississippian Subperiod some 410 to 325 million years ago and subjected to uplift and folding during the Ouachita orogeny of the Atokan Epoch (early Pennsylvanian Subperiod), Novaculite is a very tough stone that is resistant to erosion and thus, the various layers of Novaculite stand out as ridges in the Ouachita Mountains. Thus, due to both its availability and its composition, it has been mined since ancient times for use as arrowheads and spear heads as well as in more modern times for use as sharpening stones.
Stropping a knife is a finishing step. This is often done with a leather strap, either clean or impregnated with abrasive compounds (e.g. chromium(III) oxide or diamond), but can be done on paper, cardstock, cloth, or even bare skin in a pinch. It removes little or no metal material, but produces a very sharp edge by either straightening or very slightly reshaping the edge. Stropping may bring a somewhat sharp blade to "like new" condition.

✅ PREMIUM QUALITY : Our products have been inspected by a reputable third party inspection company. Each product has been checked,put under a durability and functionality test before shipped to you. NO COMPROMISE on quality! This simple-yet-unparalled award winning tool is used by everyone from stay at home moms to various professionals. Don’t forget to buy this as a PERFECT GIFT for your family & friends.
Let’s talk about the tip of the knife, the burr needs to be formed here as well. Here is a simple trick that works, I like keeping things simple. As you get to the tip area of the knife, the front inch, raise your elbow so that it is parallel to the ground, you can also raise your sharpening angle very slightly but just raising your elbow will perform wonders and likely eliminate the tip sharpening area issue, it is an issue for some.
Select the grit of the stone. Sharpening stones are available with different grit sizes. For example, you can choose fine, medium and coarse stones. You should use a coarse stone followed by a fine grit if your knives are dull. If your knives have been sharpened recently or they aren't too dull, consider using a medium grit. Try to use a grit level ranging from 325 (for coarse) to 1200 (for extra fine).[3]

Some of the videos I watched suggested soaking the stone for 12-15 minutes prior to use. One suggested using vegetable oil on the surface versus water/soaking (I used water and presoaking it for 15-minutes). So instead of a simple 'out-of-the-box-and-use' approach, it required a bit of research before sharpening a knife. Otherwise I would have given this product a 5-star rating.

I would say they are worth the money. Go for it. I took a blunted Pampered Chef kitchen knife from completely dull to razor sharp in about an hour (of bumbling and repairing mistakes LOL) heavy grinding. If you have a severely damaged blade, grab one of those cheesey two sided stones from Harbor Freight to do your heavy grinding. From there these stones will work very well.
Choose the style of stone. You'll need to choose a natural or synthetic stone that can be used wet (soaked in water), with oil, or dry. There are also diamond stones that are actually very small diamonds attached to a metal surface. Stones that are soaked in water are softer stones which means you can quickly sharpen your knives. Unfortunately, these stones will wear down faster than the others. Oil stones are the least expensive and they're made of a harder material.[2]
For instance, American Novaculite (aka Washita and Arkansas Stones) is a form of metamorphic Chert that produces some of the best known and best loved natural whetstones in existence. Then, there is a form of Belgian Coticule which has been known for providing extra-keen edges since Roman times and, there is a Japanese Siliciclastic sedimentary stone (aka Japanese Water Stones) which consist of a fine silicate particles suspended in a clay matrix. Plus, there are also various types of man-made whetstones available such as Silicon Carbide (aka Crystalon) stones and Aluminum Oxide (aka India Stones) as well as a synthetic Corundum (aka Ruby) rod and Aluminum Oxide impregnated ceramic rods as well as several different types of diamond hones.
Diamond hones are made from very small, industrial grade, diamonds adhered to the face of a metal or plastic plate. Also, because Diamonds are so much harder than any of the other sharpening materials, they tend to cut very fast and last much longer than the other whetstone materials. But, they are also often more expensive to purchase. In addition, Diamond Stones generally consist of three different styles consisting of a solid metal plate coated with an adhesive and diamond dust with holes in the plate to allow the swarf to escape, a solid plate without holes for sharpening tools with corners that might catch in the holes, and a plastic plate with islands of exposed plastic interspersed with the adhesive and diamond dust to act as a lubricant.
The kind of tech we love: compact, reliable, durable, attractive and cheap. Purists may feel that other sharpeners will produce a more perfect result but for 99% of the human race this sharpener will be everything the doctor ordered. Your blades stay sharp for a good long time thanks to the 2-stage sharpening process and if you’re a left handed chef you’ll love the fact that it works just as effectively for you as for anyone else. 

Removing the burr is fairly simple. You'll need a leather strop or block (this sort of thing), which is designed to catch the metal fibres from the knife. You could do it with a fibrous tea towel or some newspaper if you like, but I'd suggest going with leather to begin with. The motion is fairly similar to sharpening. Draw the knife over the leather, going away from the edge at roughly the same angle as when you sharpened. 
A great sharpener for all your kitchen knives the CS2 also makes a smart addition to the gear when you’re going away on a family camping trip. It will also do a bang-up job on your hunting, pocket, boning knife and more. As mentioned it does require just a bit of getting used to in order to achieve optimal results but nothing too involved. A simple, effective, no-frills sharpener.
It looks like it can be a Sci-Fi film prop. This is a 2 stage type of sharpening system. You'll get a non slip cushion with it which is at the bottom offering stability for the user. It's ergonomic handle provides a comfortable and easy grip. This cushion offers the stability needed when sharpening and polishing your pocket knife to it's absolute razor sharpness. The sharpener does the work as you hold down the grip and simply place your pocket knife to get sharpened by the motions of the ceramic and diamond sharpener wheels. Simply run your dull knives through the device and you'll get the results you've been looking for. This one will definitely help you when you learn how to sharpen a pocket knife on the Priority Chef.